background image

Hearthstone Quality Home Heating Products, Inc. 

Bristol DX Model 8762 

 

 

 

(S’ASSURER  QUE  LE  BRÛLEUR  ET  LE 
COMPARTIMENT 

DES 

COMMANDES 

SONT 

PROPRES. 

 

VOIR 

LES 

INSTRUCTIONS 

D’INSTALLATION 

ET 

D’UTILISATION 

QUI 

ACCOMPAGNENT L’APPAREIL.)

 

Hot Surfaces 

Certain  exposed  surfaces  of  the  Bristol  will  reach 
high 

temperatures 

during 

normal 

operation.  

Clearances to combustibles must be maintained,  as 
specified  in  the  “Clearances  To  Combustibles” 
section of this manual.  

 

DUE  TO  HIGH  TEMPERATURES  THE  APPLIANCE 
SHOULD  BE  LOCATED  OUT  OF  TRAFFIC  AND 
AWAY 

FROM 

FURNITURE, 

DRAPERIES, 

CLOTHING AND FLAMMABLE MATERIALS.   

 

CHILDREN  AND  ADULTS  SHOULD  BE  ALERTED 
TO 

THE 

HAZARDS 

OF 

HIGH 

SURFACE 

TEMPERATURES  AND  SHOULD  STAY  AWAY  TO 
AVOID BURNS TO SKIN OR CLOTHING IGNITION.  

 

CAREFULLY  SUPERVISE  YOUNG  CHILDREN 
WHEN  THEY  ARE  IN  THE  SAME  ROOM  AS  THE 
APPLIANCE.  TODDLERS,  YOUNG  CHILDREN, 
AND  OTHERS  MAY  BE  SUSCEPTIBLE  TO 
ACCIDENTAL  CONTACT  BURNS.  A  PHYSICAL 
BARRIER  IS  RECOMMENDED  IF  THERE  ARE  AT 
RISK INDIVIDUALS IN THE HOUSE. TO RESTRICT 
ACCESS  TO  A  FIREPLACE  OR  STOVE,  INSTALL 
AN  ADJUSTABLE  SAFETY  GATE  TO  KEEP 
TODDLERS,  YOUNG  CHILDREN,  AND  OTHER  AT 
RISK  INDIVIDUALS  OUT  OF  THE  ROOM  AND 
AWAY FROM HOT SURFACES. 

 

CLOTHING  OR  OTHER  FLAMMABLE  MATERIAL 
SHOULD  NOT  BE  PLACED  ON  OR  NEAR  THE 
APPLIANCE. 

 

(SURVEILLE 

LES 

ENFANTS.  

GARDER  LES  VÊTEMENTS,  LES  MEUBLES, 
L’ESSENCE  OU  AUTRES  LIQUIDES  À  VAPEUR 
INFLAMMABLES LIN DE L’APPAREIL.)

   

 

CLEAN  THE  AREA  AROUND,  UNDER,  AND 
BEHIND  THE  UNIT  ON  A  REGULAR  BASIS  TO 
PREVENT  THE  ACCUMULATION  OF  DUST  AND 
LINT.  

Ceramic Logs, & Burner 

If  the  decorative  ceramic  log,  or  burner  material 
supplied  with  the  Bristol  is  damaged  or  parts  are 
missing,  they  must  be  replaced  with  the  same,  or 
approved  Hearthstone  replacement  parts.  These 
components affect the combustion quality and safety 
of  the  heater.  Do  not  replace  ceramic  logs,  or  the 
burner with unapproved ceramic components or any 
other material.  

We recommend  you always wear  gloves and safety 
goggles  while  handling  the  ceramic  log  set,  and 
burner materials. 

Electrical Hazard 

If  present,  any  three-prong  grounded  plug  must  be 
plugged  directly  into  a  properly  grounded  three-
prong  receptacle.  Do  not  cut  or  remove  the 
grounding prong from any plug or otherwise attempt 
to circumvent the grounding protection provided with 
the unit. The Bristol must be electrically grounded in 
accordance  with  local  codes,  or  in  the  absence  of 
local  codes,  with  the  National  Electrical  Code, 
ANSI.NFPA  70  in  the  U.S.  or  CSA  C22.1  Canadian 
Electrical Code in Canada.  

Do Not Light Pilot or Burner by Hand 

The  pilot  light  on  this  gas  heater  is  lit  using  an 
electronic ignition module as described elsewhere in 
this  manual.  Never  attempt to light  the  pilot  or  main 
burner by hand with a match or lighter. 

Mobile Home Installations 

This  appliance  may  be  installed  in  an  aftermarket 
permanently  located,  manufactured  (mobile)  home, 
where  not  prohibited  by  local  codes. 

(Cet  appareil 

peut  être  installé  dans  un  maison  préfabriquée 
(mobile)  déjá  installée  á  demeure  si  les  réglements 
locaux le permettent. 

Summary of Contents for Bristol DX










































Reviews: