background image

Hearthstone Quality Home Heating Products, Inc.

                                                   

 

Stowe 3 Model 8323  

38 

 

 
 
Setting P2 ON Time 

•  Once P1 times are set, briefly press 

SET

 button 

to scroll to setting P2 ON time. 
P2 and the sun icon are displayed and the time 
flashes. 

•   See instructions SETTING P1 ON TIME. 
 

Setting P2 OFF Time 

•   Briefly press 

SET

 button to scroll to setting P2 

OFF time. P2 and the crescent moon icon are 
displayed and the time flashes. 

•   See instructions SETTING P1 OFF TIME. 
•    This concludes programming Timers P1 and P2.  

Press OFF or wait. The handset will automatically 
save your changes. 

 

TO TURN OFF GAS TO APPLIANCE 

 
1.  Place ON/OFF switch  in 0 (OFF position). 
2.  If gas control is accessible turn main valve knob 

to the OFF full clockwise  position. 

3.  Replace appliance access cover. 

 

 
AUTOMATIC TURN DOWN 
 
6 Hour no Motor Movement 

(CSA version) 
•   Manual Model/Temperature/Timer Mode: The 

valve will turn to pilot flame if there is no change 
in flame height for a 6 hour period. In 
Temperature/Timer Mode if the ambient room 
temperature changes, the flame height will adjust 
automatically to maintain set temperature, and 
the fire will continue to function normally. The 
valve will turn to pilot flame if the set temperature 
and the ambient room temperature remain the 
same over a 6 hour period. 

 
Receiver Overheating 

•   Valve turns to pilot flame if the temperature in the 

receiver is higher than 140of (60°C). The main 
burner comes back on only when the temperature 
is below 140°F (60°C). 

 

AUTOMATIC SHUT OFF 
 
Low Battery Receiver 

•   With low battery power in the receiver the system 

shuts off the fire completely. This will not happen 
if the power supply is interrupted. 

 

Five Day Shut Off 

(CSA version) 

•   The system shuts off the fire completely if there is 

no change in flame height for 5 days. 

 
NOTE:  Before the next ignition there is a 2 minute  

 

   

waiting period. 

 
Routine Maintenance 
and Care 

 

Your Champlain requires minimal routine 
maintenance and care. Ensure the unit is cool 
and off when cleaning, or servicing. 

 

 

WARNING:

 

DO NOT SUBSTITUTE MATERIALS.

  

 

For replacement parts, or for information about parts 
or service, contact your local Hearthstone dealer. 

Any  safety  screen  or  guard  removed  for 
servicing an appliance must be replaced prior to 
operating  the  appliance.   

Tout  écran  ou 

protecteur  retiré  pour  permettre  l’entretien  de 
l’appareil  doit  être  remis  en  place  avant  de 
mettre l’appareil en marche. 

 

Cleaning 
 

 

WARNING: DO NOT CLEAN THE UNIT WHEN HOT.  

 

The  unit  should  receive  regular  cleaning  on,  under, 
and  around  the  stove  to  prevent the  buildup  of  dust 
and  lint.  The  exterior  surfaces  of  the  unit  can  be 
cleaned  using  soap,  water,  and  a  soft  cloth.  Do  not 
use abrasive or chemical cleaners and take care not 
to scratch the glass or enamel finish (if so equipped) 
when  cleaning  the  unit.  The  use  of  chemical  wax 
based  cleaners  or  polishes  are  not  recommended 
due to the potential for discoloration of the castings, 
or  enamel  when  the  residue  of  the  cleaners  or 
polishes  is  exposed  to  heat.  Excessive  buildup  of 
dust,  spider  webs,  or  room  air  contamination  may 
cause odors when the stove is hot.  

Monthly (or as needed):

 

 

Glass Cleaning 

As  fuel  gas  may  contain  some  impurities;  it  will  be 
necessary  to  clean  the  inside  of  the  glass 
occasionally.  Do  not  use  abrasive  cleaners. 
Scratching  the  glass  will  weaken  the  integrity  of  the 
glass. 

Do not clean the glass when hot!

 Allow the 

glass to cool and apply a mild window cleaning fluid. 
Special  gas  appliance  window  cleaner  is  available 
from your local Hearthstone dealer. 

Summary of Contents for Champlain 8302

















































Reviews: