background image

Hearthstone Quality Home Heating Products, Inc                                                                 

             CHAMPLAIN Model 8302  

 

Installation Preparation 

C

ODES

 

Adhere  to 

all

 

local  codes

  or,  in  their  absence, the 

latest edition of THE NATIONAL FUEL GAS CODE 
ANSI  Z223.1  (NFPA  54)  or  CAN/CGA  B149 

 

(Installer  l’appareil  selon  les  codes  ou  règlements 
locaux,  ou,  en  l’absence  de  tels  règlements,  selon 
les Codes d’installation CAN/CGA-B149.) 

Installation Codes can be obtained from:

 

AMERICAN NATIONAL STANDARDS 
INSTITUTE, INC.

 

1430 BROADWAY 
NEW YORK, NY 10018 
www.ansi.org 

NATIONAL FIRE PROTECTION 
ASSOCIATION, INC.

 

BATTERY MARCH PARK 
QUINCY, MA 02269 
www.nfpa.org 

The  appliance  when  installed  must  be  electrically 
connected  and  grounded  in  accordance  with  local 
codes  or,  in  the  absence  of  local  codes,  with  the 
current  NFPA  70-National  Electrical  Code  or  CSA 
C22.1-Canadian Electric Code. 

A  manufactured  home  (mobile)  OEM  installation 
must 

conform 

to 

the 

Manufactured 

Home 

Construction  and  Safety  Standard,  Title  24  CFR, 
Part  3280  (U.S.)  or  Standard  for  Manufactured 
Home 

Installation, 

ANSI/NCBCS 

A225.1 

or 

Standard  for  Gas  Equipped  Recreational  Vehicles 
and  mobile  Housing,  CSA  Z240.4.CAN/SCA  Z240 
MH  (Canada).  This  appliance  is  only  for  use  with 
the type(s) of gas indicated on the rating plate. 

Cet 

appareil  peut  être  installé  comme  du  matériel 
d’origine  dans  une  maison  préfabriquée  (É.-U. 
seulement)  ou  mobile  et  doit  être  installé  selon  les 
instructions  du  fabricant  et  conformément  à  la 
norme  Manufactured  Home  Construction  and 
Safety 
Standard,  Title  24  CFR,  Part  3280  aux  États-Unis 
ou  à  la  norme  CAN/CSA-Z240  Série  MM,  Maisons 
mobiles  au  Canada.  Cet  appareil  doit  être  utilisé 
uniquement  avec  les  types  de  gaz  indiqué  s  sur  la 
plaque signalétique. 

This appliance is equipped for use at 0 to 2000 feet 
(0-610  meters)  altitude. 

(Cet  appareil  est  equipè 

pour  des  altitudes  compries  entre  0  et  2000  pieds 
(0-610 m) seulement.)

  

Items Required for Installation 

  External regulator (for propane (LP) only) 
  LP conversion kit (for propane only)) 
  Piping which complies with local codes 

  Pipe sealant approved for use with                                

propane (LP) (resistant to sulfur compounds). 

  Manual shutoff valve 
  Sediment trap (

see page 20

  Pipe wrench 
  Phillips head screwdriver 
  7/16-inch wrench 
 

5/23” (4mm) allen wrench 

  Other parts as required by local code 
  Safety Glasses 
  Gloves 

 

Packing List 

1- Champlain 8302 Gas-Fired Heater 
1- Pan Burner 
1- 

Owner’s Packet (manual, warranty card) 

1- LP Conversion Kit 
6- Decorative Ceramic Logs (in separate box) 
1- Bag of Platinum Bright Embers 

 

 

Note:  Vent  kits  and  components  are  supplied 
separately. 

Failure 

to 

use 

the 

venting 

components  approved  by  Hearthstone  for  this 
appliance will void your warranty.

 

 

Unpacking and Inspection 

 

 

Hearthstone  packages  your  Champlain    to 
withstand  normal  shipment  without  damage. 
However,  damage  can  still  occur  during  transit. 
Take  care  to  inspect  for  damage  when  unpacking 
and installing the unit.    

 

DO  NOT  INSTALL,  OR  PUT  INTO  SERVICE,  A 
DAMAGED OR INCOMPLETE HEATER.

   

Remove  the  shrink-wrap  and  other  packaging 
materials  taking  care  not  to  damage  the  stove’s 
finish.  Inspect  the  Champlain  for  visible  or 
concealed damage. The unit should be square and 
true.  The  sheet  metal  parts  should  be  smooth  and 
free  of  bends  and  dents.  Any  enameled  cast  iron 
should  be  free  of  chips  or  cracks.  If  visible  or 
concealed  damage  is  found  or  suspected,  contact 
your dealer for instructions. 

Always  use  gloves  and  eye  protection  when 
handling  the  decorative  ceramic  fire  logs  and 
burner. Use care when handling these parts as they 
are  fragile  and  subject  to  damage  and  breakage  if 
handled roughly.  
See  the  firebox  access  instructions  on  page  9. 
Unpack  and  inspect  the  logs  for  damage.  Inspect 
the metal burner as well. Open the other boxes and 
inspect  the components.  If log, burner  or any  other 
component  damage  is  encountered,  contact  your 
dealer  for  a  replacement.  Otherwise,  set  the  logs 

Summary of Contents for Champlain 8302

















































Reviews: