background image

Hearthstone Quality Home Heating Products, Inc                                                                 

             CHAMPLAIN Model 8303 

 

INTRODUCTION 

 

Congratulations on your purchase of the Champlain 
Model 8303, Gas-Fired Direct-Vent heater. The 
Champlain, by Hearthstone, incorporates the latest in 
direct vent gas technology, which will provide you 
with clean, efficient heat for years to come. The 
enameled or painted cast iron gives the Champlain a 
pleasing look that is maintained with minimum care. 

 

The  Champlain  will  provide  you  with  years  of 
practical  and  convenient  service.  However,  as  with 
any  gas  appliance,  the  unit  must  be  properly  and 
safely  installed  and  maintained  by  qualified  service 
personnel to ensure safe and trouble-free operation. 
 

C

HAMPLAIN 

M

ODEL 

8303

 

F

EATURES

:

 

 

1.  SIT 820 valve system 
2.  6-piece log set   
3.  Safety Barrier Screen 
4.  Platinum Bright Embers. 
5.  Optional blower 

 

 

Part # 

Description 

8303-0010NP 

Matte Black 

8303-0020NP 

Brown Enamel 

 

 

 
 

 

Read this Owner’s Manual 

 
Operate  and  maintain  this  gas  heater  according  to 
the  instructions  in  this  manual.  For  your  safety,  and 
years of trouble free operation, read this manual in its 
entirety.

  

 

 

 

Heater Must Be Installed and Maintained By 
Qualified Service Personnel 

Verify the gas connections and venting systems meet 
the  requirements  of  local,  regional  or  national 
installation  codes.  Qualified  service  personnel  must 
inspect  the  gas  heater  before  use,  and  at  least 
annually. 

Manufactured & warranted by: 

Hearthstone Quality Home heating Products, Inc. 
 
317 Stafford Ave. 
Morrisville, VT 05661 

www.hearthstonestoves.com

 

inquiry@hearthstonestoves.com

 

 

SAFETY

 

INFORMATION 

Your Champlain is an attractive and extremely efficient 
heater, utilizing today’s best technologies. By following 
a few simple safety precautions and by performing 
minimal maintenance, the unit will remain appealing 
while providing years of quality performance. 

 

The installation must conform to local codes or, in the 
absences  of  local  codes,  the  current  National  Fuel 
Gas  Code,  ANSI  Z223.1  (NFPA  54)  or  CAN/CGA 
B149  Installation  Code.  (

Installer  l’appareil  selon  les 

codes ou réglements locaux, ou, en l’absence de tells 
réglements, selon les Codes d’installation CAN/CGA 
B149

.) 

 

 

CAUTION:  DO  NOT

 

USE  THIS  APPLIANCE  IF  ANY 

PART WAS UNDER WATER. IMMEDIATELY CALL A 
QUALIFIED  SERVICE  TECHNICIAN  TO  INSPECT 
THE HEATER AND TO REPLACE ANY PART OF THE 
CONTROL SYSTEM AND GAS CONTROL THAT HAS 
BEEN UNDER WATER. (NE PAS SE SERVIR DE CET 
APPAREIL  S’IL  A  ÉTÉ  PLONGÉ  DANS  L’EAU, 
COMPLÉTEMENT  OU  EN  PARTIE.  APPELER  UN 
TECHNICIEN 

QUALIFIÉ 

POUR 

INSPECTOR 

L’APPAREIL  ET  REMPLACER  TOUTE  PARTIE  DU 
SYSTÉME  DE  CONTRÔLE  ET  TOUTE  COMMANDE 
QUI ONT ÉTÉ PLUNGES DANS L’LAU.)
 

 

During  the  first  few  hours  of  operation  the  appliance 
may  produce  smoke  and/or  odor.  This  is  normal 
during  the  first  several  burns  and  also  after  long 
periods  when  the  stove  is  not  burned.  During  these 
initial  burns,  open  a  window(s)  to  assist  in  the 
removal of the smoke/odor. 

 

The appliance and its individual shutoff valve must be 
disconnected  from  the  gas  supply  piping  system 
during  any  pressure  testing  of  that  system  at  test 
pressures  in  excess  of  ½  psig.  (3.5k  Pa).  The 
appliance  must  be  isolated  from  the  gas  supply 
piping system by closing its individual manual shutoff 
valve  during  any  pressure  testing  of  the  gas  supply 
piping system at test pressures equal to or less than 
½ psig (3.5k Pa). 

 

Fire Hazard 

Do  not  store  or  use  gasoline  or  other  flammable 
vapors  or  liquids  in  the  vicinity  of  this  appliance. 
Locate  the  Champlain  out  of  traffic  areas  and  away 
from  furniture,  draperies,  clothing,  and  flammable 
material. 
 

Vent Only to the Outside. 

Never vent the gas 

heater to other rooms or buildings.

 

 

Service Caution 

If  you  believe  your  Champlain  is  not,  in  any  way, 
performing 

properly, 

immediately 

discontinue 

Summary of Contents for Champlain 8303




































Reviews: