background image

Hearthstone Quality Home Heating Products, Inc.                                   

                                BARI Model #8180                                      

Symptom 

Possible Cause 

Corrective Action 

3. Pilot burning, no gas 
to main burner, valve 
knob in the "ON" 
position, thermostat 
and/or on/off/t'stat 
switch in the "ON" 
position. 
  
 

 

A. Thermostat switch or wires 
defective. 
 
B. Thermopile may not be 
generating sufficient voltage. 
 
C. Plugged burner orifice. 

A. Check thermostat/wiring for proper connections. 
Place jumper wire across terminals at thermostat. If 
burner comes on, replace defective thermostat. If not 
OK, place jumper across thermostat wires at gas 
valve. If burner comes on, tighten connections, or 
replace faulty wires. 
 
B. Check thermopile output, using a milli-volt meter. 
Take the readings across generator terminals of the 
gas valve. (TPTH and TP). Milli-volt reading should 
be greater than 325 mV. If not, replace the pilot 
assembly. If the meter reading is OK, but the burner 
does not come on, replace the gas valve. 
 
C. Remove and check burner orifice - clean or 
replace. Note: do not use any metal cleaning device, 
as this may damage the orifice. 

4. Pilot and burner 
come on, but go out 
after some warm-up. 
  

A.  Inconsistent or insufficient 

flame on thermopile. 
 

B.  Insufficient gas pressure. 

 

C. Excessive 

draft.

 

A. Adjust pilot flame size and assure that the flame is 
aimed directly at the thermopile. 

B. Check line pressure to ensure that the correct inlet 
pressure is present for the type of gas being used. If 
propane pressure is inconsistent, check for water 
condensation at the regulator. 

C. Check Restriction settings per this manual. 

5. Frequent pilot 
outage problem. 

A. Pilot flame may be too low or 
blowing, (high), causing the pilot 
safety to drop out. 
 
B. Excessive draft 

A. Clean and/or adjust the pilot flame for maximum 
impingement on the thermopile and thermocouple. 
 
B. Check Restriction settings per this manual. 
 

6. Glass fogs 

A. A normal result of gas 
combustion. 

A. After the heater has warmed up, the glass should 
clear. 

7. Blue Flames 
  

A. A normal result during the first 
20 minutes. 
 

 

A. Flames should begin to turn more yellowish after 
about 20 minutes of burning. 
 
B. If the blue color persists; adjust the air shutter for a 
proper burn. 

 

 

 

29

Summary of Contents for hase-Bari 8180

































Reviews: