background image

Hearthstone Quality Home Heating Products, Inc.                                                                    

   

         Bari Model #8180 

I

NSTALLATION 

P

REPARATION

H

EARTH 

R

EQUIREMENT 

/

 

F

LOOR 

P

ROTECTION

 

You can place the Bari directly on any non-
combustible surface, or wood floor. When installing 
the Bari on carpet, vinyl, or any other combustible 
floor other than wood flooring, it must be installed on 
any non-combustible, or wood panel extending the 
full width and depth of the stove.  

C

LEARANCE 

T

C

OMBUSTIBLES

 

Due to high surface temperatures, install the unit out 
of traffic and away from furniture and draperies. Do 
not place clothing and other flammable material on 
or near the heater. When positioning the unit always 
maintain adequate clearances around air openings 
into the combustion chamber and allow for adequate 
ventilation. You must maintain minimum clearances 
to combustibles as shown in the illustrations of this 
section. 

Ensure you consider the need for access to the gas 
control valve access door on the front of the unit as 
well as full access for periodic cleaning and 
servicing.  

 

CAUTION: THESE CLEARANCES REPRESENT 
MINIMUM  
DISTANCES IN ALL CASES, WHICH, 
THROUGH TESTING IN AN INDEPENDENT 
LABORATORY TO ANSI AND CSA STANDARDS, 
WILL PREVENT FIRE OR SPONTANEOUS 
COMBUSTION. WE DO NOT CONTROL THE 
COMBUSTIBLE MATERIALS EXPOSED TO HEAT 

BY THIS PRODUCT; THEREFORE, AN 
ASSESSMENT MUST BE MADE BY THE 
INSTALLER TO PREVENT CONSEQUENTIAL 
DAMAGE OF WALLS AND FLOORING. 

O

PENING THE 

F

RONT 

D

OOR

 

In order to gain access to the firebox you must open 
the front door. The door has a handle on the side 
that will latch the door shut; however there is also a 
mounting screw on the lower right hand side that 
locks the door in place. (

See Figure 3) 

To access 

this screw you must open the lower control door 
located just below the front door. Before using the 
latch, remove the mounting screw using a 4mm or 
5/32” Allen wrench. 

Replace this screw when the 

door is closed for operation, as the latch cannot 
be relied on to maintain a proper permanent door 
seal.

  

I

NSTALLING THE 

S

TONE 

P

ANELS

 

See the Stone Installation Instructions included in 
the Manual Packet for specific information needed 
for mounting the stones.   

 

Note:

 the stones on this stove are large and 

heavy (150 pounds total).  

Use a second person to assist in mounting the 
panels to avoid injury, or damage to the panels. 
Despite the mass of each piece of soapstone, they 
will break if dropped. 

 

 

       

 

Figure 2 - Clearance to Combustibles  

 Figure 3 - Remove Screw for Firebox Access 

 

 

 

 

9

Summary of Contents for hase-Bari 8180

































Reviews: