HearthStone Santa Fe 8761, Owner'S Manual

Hearthstone Quality Home Heating Products, Inc.                                                              

   SANTA FE Model 8761                                                   

11 

Note: The Standard Horizontal Vent Kit does 
not require a restrictor.

 
The vent/air intake termination clearances above 
the high side of an angled roof as follows: 

Roof Pitch 

Feet 

Meters

Flat to 6/12 

1 

0.3 

7/12 to 9/12 

2 

0.6 

10/12 to 12/12             4 

1.2 

13/12 to 16/12   

6 

1.8 

17/12 to 21/12             8 

2.4

Figure 6 

A

PPROVED 

V

ENTING 

S

YSTEM 

C

OMPONENTS

Component Description    

90

 0

 Elbow 

45

 0

 Elbow 

6" Straight 
9" Straight 
12" Straight  
24" Straight  
36" Straight  
48" Straight  
11"-14 

5/8"

 Adjustable Pipe Length 

Horizontal Vent Cap  
Vertical Vent Cap 
Snorkel 36” 
Vinyl Siding Standoff 4 x 6

 5/8”

Round Ceiling Support Wall  
 

Thimble Covers  

Wall thimble 

 
If the vent air intake system, for any reason, 
is disassembled, it must be reinstalled per the 
instructions provided for in the initial 
installation or in this manual. 

 
V

ENT 

C

ONFIGURATION 

O

PTIONS

 
I.

S

TANDARD 

H

ORIZONTAL 

I

NSTALLATION

Kit #93-65000) 
 

Minimum horizontal run is 9” 

N

OTE

: 

Install the 45º elbow over the outer collar.  Place 
the elbow so that the twist lock end is pointing 
up. Install the 2’ pipe section into the elbow by 
fully inserting it, and turning approximately ¼ 

turn clockwise until the two sections are fully 
locked. Install the 90º elbow in similar fashion. 
 

N

OTE

: B

E SURE THERE IS NO 

W

IRING OR 

P

LUMBING IN THE CHOSEN WALL LOCATION

. 

Move the stove and pipe assembly back until the 
90º elbow is flush to the wall.  The 2’vertical 
pipe should be parallel to the wall.  Draw a 
circle around the pipe.  Use the center of this 
circle as the center point of the 10” 

x 

10” square 

wall pass through.  Cut and frame the wall for 
the vent pipe.

Install the horizontal vent 

termination on the outside of the wall.  Make 
sure both of the retaining straps extend through 
the interior wall.  Before attaching the vent 
termination to the outside of the house, run a 
bead of non-hardening mastic around the outside 
edges, between the vent termination and the 
wall.  The arrow on the end cap should point up.  
Secure the cap to the wall with the appropriate 
screws. 
 
Put the adjustable (11”-14”) pipe into the 
horizontal vent cap, (the vent pipe must extend 
into the horizontal vent cap a minimum of 1 ¼”).  
Move the stove and vent pipe into position, 
insert the adjustable (11”-14”) pipe into the 90

Ε

elbow, twist lock it.  Secure the straps from the 
horizontal vent termination to the interior pipe 
with two sheet metal screws, keeping screws as 
close to the wall thimble as possible.  Bend or 
cut the excess strapping so the thimble cover 
will fit properly.   Screw the thimble cover to the 
wall. 

•

The adjustment range of the wall 
thickness for this configuration is 
3”min- 9”max.