background image

Hearthstone Quality Home Heating Products, Inc. 

   Stowe DX Model 8322 

 

 

 

Safety Information 

Your  Stowe  is  an  attractive  and  extremely  efficient 
heater,  utilizing  today’s  best  technologies.  By 
following  a  few  simple  safety  precautions  and  by 
performing minimal maintenance, the unit will remain 
appealing 

while 

providing 

years 

of 

quality 

performance. 

 

The  installation  must  conform  to  local  codes  or,  in 
the  absences  of  local  codes,  the  current  National 
Fuel  Gas  Code,  ANSI  Z223.1  (NFPA  54)  or 
CAN/CGA 

B149 

Installation 

Code. 

(

Installer 

l’appareil selon les codes ou réglements locaux, ou, 
en  l’absence  de  tells  réglements,  selon  les  Codes 
d’installation CAN/CGA B149

.) 

 

 

CAUTION: DO NOT

 

USE THIS APPLIANCE IF ANY 

PART  WAS  UNDER WATER.  IMMEDIATELY  CALL 
A QUALIFIED SERVICE TECHNICIAN TO INSPECT 
THE  HEATER  AND  TO  REPLACE  ANY  PART  OF 
THE  CONTROL  SYSTEM  AND  GAS  CONTROL 
THAT  HAS  BEEN  UNDER  WATER.  (

NE  PAS  SE 

SERVIR  DE  CET  APPAREIL  S’IL  A  ÉTÉ  PLONGÉ 
DANS  L’EAU,  COMPLÉTEMENT  OU  EN  PARTIE. 
APPELER  UN  TECHNICIEN  QUALIFIÉ  POUR 
INSPECTOR L’APPAREIL ET REMPLACER TOUTE 
PARTIE  DU  SYSTÉME  DE  CONTRÔLE  ET  TOUTE 
COMMANDE  QUI  ONT  ÉTÉ  PLUNGES  DANS 
L’LAU.)

 

 

During the first few hours of operation the appliance 
may  produce  smoke  and/or  odor.  This  is  normal 
during  the  first  several  burns  and  also  after  long 
periods  when  the  stove  is  not  burned.  During  these 
initial  burns,  open  a  window(s)  to  assist  in  the 
removal of the smoke/odor. 

 

The  appliance  and  its  individual  shutoff  valve  must 
be  disconnected  from  the  gas  supply  piping  system 
during  any  pressure  testing  of  that  system  at  test 
pressures  in  excess  of  ½  psig.  (3.5k  Pa).  The 
appliance  must  be  isolated  from  the  gas  supply 
piping  system  by  closing  its  individual  manual 
shutoff  valve  during  any  pressure  testing  of  the  gas 
supply  piping  system  at  test  pressures  equal  to  or 
less than ½ psig (3.5k Pa). 

Fire Hazard 

Do  not  store  or  use  gasoline  or  other  flammable 
vapors  or  liquids  in  the  vicinity  of  this  appliance. 
Locate the Stowe out of traffic areas and away from 
furniture, 

draperies, 

clothing, 

and 

flammable 

material. 

Vent Only to the Outside 

Never  vent  the  gas  heater  to  other  rooms  or 
buildings. 

Service Caution 

If  you  believe  your  Stowe  is  not,  in  any  way, 
performing 

properly, 

immediately 

discontinue 

operation until the unit is inspected and approved by 
qualified  service  personnel.    Prior  to  servicing  the 
unit,  turn  the  gas  to  the  valve  off,  and  disconnect 
any electrical source. Ensure the unit is cool prior to 
servicing  and  cleaning.  Replace  any  safety  screen, 
guard, or component removed during servicing prior 
to operation. Use of any components not supplied by 
Hearthstone  on  the  stove  voids  all  warranties. 

Do 

not substitute components. 

Proper Fuel 

This gas heater is designed to burn natural gas (NG) 
or  with  conversion,  liquid  propane  (LP).  Never  burn 
any  fuel  gas  not  intended  for  use  with  this  unit. 
Never  burn  paper,  wood,  or  other  materials  in  this 
appliance. 

This  heater  is  factory  equipped  to  burn  natural  gas 
(NG). To burn propane (LP),  you must purchase  LP 
conversion kit #97-56104.  

This appliance is only for use with the type(s) of gas 
indicated  on  the  rating  plate.  This  appliance  is  not 
convertible  for  use  with  other  gases,  unless  a 
certified  kit  is  used.

  Cet  appareil  doit  être  atilisé 

uniquement  avec  les  types  de  gas  indiqués  sur  la 
plaque  signalétique.  Ne  pas  l’utiliser  avec  d’autres 
gas sauf si un kited conversion certifié est installé. ) 

 

WARNING:  THIS  GAS  APPLIANCE  MUST  NOT  BE 
CONNECTED  TO  A  CHIMNEY  FLUE  SERVING  A 
SEPARATE  GAS  OR  SOLID-FUEL  BURNING 
APPLIANCE 

 

WARNING:    DO  NOT  OPERATE  THE  APPLIANCE 
WITH  THE  FRONT  GLASS  REMOVED,  CRACKED, 
OR  BROKEN.    REPLACEMENT  OF  GLASS 
SHOULD  BE  DONE  BY  A  LICENSED  OR 
QUALIFIED  SERVICE  PERSON.    ONLY  OPEN 
FRONT  FOR  ROUTINE  SERVICE.    DO  NOT  SLAM  
FRONT OR STRIKE GLASS.

 

 

WARNING: HEARTHSTONE RECOMMENDS THAT 
ONLY AN NFI CERTIFIED SERVICE TECHNICIAN 
INSTALLS, AND REPAIRS THIS APPLIANCE. A 
QUALIFIED SERVICE TECHNICIAN MUST 
INSPECT THE APPLIANCE BEFORE USE, AND AT 
LEAST ANNUALLY. MORE FREQUENT CLEANING 
MAY BE REQUIRED DUE TO EXCESSIVE LINT 
FROM CARPETING, BEDDING MATERIAL, PETS, 
ETC. IT IS IMPERATIVE THAT THE CONTROL 
COMPARTMENTS, BURNERS, AND CIRCULATING 
AIR PASSAGES OF THE APPLIANCE ARE KEPT 
CLEAN AND FREE OF OBSTRUCTIONS.

 

(S’ASSURER QUE LE BRÛLEUR ET LE 

f i r e - p a r t s . c o m

Summary of Contents for Stowe DX 8322










































Reviews: