HearthStone Tribute DV 8050 Owner'S Manual & Installation Manual Download

Page: 29 / 36

Hearthstone Quality Home Heating Products, Inc.

Tribute DV Model #8050

ARTS

IST

Part No. Description Part

No. Description

2010-210 FOOT

7211-580 LOG:

CENTER

BOTTOM

2010-505 BOTTOM

7211-581 LOG:

CENTER

REAR

2010-520 COLUMN

7211-582 LOG:

LEFT

BOTTOM

2010-530 FRONT

7211-583 LOG:

LEFT

UPPER

2010-532 BAFFLE

7211-584 LOG:

RIGHT

SIDE

2010-535

HEAT EXCHANGER BASE

7211-517

CHARCOAL EMBERS 4OZ.

2010-537 HEAT

EXCHANGER

7211-401 KNOB:EXTENSION,ON/OFF/PILOT,SIT

(916188)

2010-540

LOWER TOP

7211-402

KNOB: EXTENSION,HI/LO,SIT (916189)

2010-545 UPPER

TOP

7211-020 FITTING:

90deg,1/8"NPTx3/8"CMP(4054-06)

3030-046 GLASS

7200-506 THERMOSTAT:

MILLIVOLT

3160-050

GASKET ; HEAT EXCHANGER

7210-103

IGNITOR:MILLIVOLT(#1244-61&1364-03)

3160-080

WINDOW TAPE 3/4" x 1/16"

5050-011

PILOT SHIELD DEFLECTOR, REAR

3160-150

HEAT EXCHANGER BASE GASKET

5050-012

PILOT SHIELD DEFLECTOR, FRONT

3160-152 PILOT

GASKET

5050-013 PILOT

SHIELD DEFLECTOR, TOP

3160-155

GASKET: EXIT

7200-248

BURNER ORIFICE NG #48

3160-157 GASKET:

INLET

7210-103 IGNITOR:MILLIVOLT(#1244-61&1364-03)

3160-051

SHUTTER BOX GASKET

7211-163

PILOT ORIFICE NG .62 MM

3170-150

PLATINUM BRIGHT EMBERS

7211-310

VALVE: GAS,SIT,50% TD,NG,CHA/STG/TUC D&B

3300-580

SAFETY RATING LABEL

7211-370

BURNER: PILOT,CON TOP,3-WAY,NG,.#199.724

3300-581

FUEL CONVERSION LABEL

7211-407

KNOB, EXTENSION CONTROL 1" ON-OFF (SIT)

5050-005

VALVE BRACKET

7211-404

KNOB, EXTENSION CONTROL 1" HI-LO (SIT #0916218)

5050-010

FIREBOX

7211-027

3/8" X 6"SS FLEX TUBE (STG/TUDOR)

5050-015 SHUTTER

7210-008 FITTING:

90deg,3/8"NPTx3/8"CMP(NUT&FER)

5050-017

SHUTTER BOX

7211-003

FITTING: STRAIGHT 1/4" NPT x 3/8"COMP

5050-020

BACK PANEL, LEFT

5050-022

BACK PANEL, RIGHT

LP CONVERSION KIT

5050-030

HEAT SHIELD

7200-125

BURNER LP ORIFICE #56

5050-050 GLASS

FRAME

7211-136 ORIFICE:

PILOT,LP,0.35mm,CONVERT TOP,SIT

5050-060 RESTRICTOR

7211-313 REGULATOR:

VALVE,LP,50%

TURNDOWN,SIT

5120-078 DAMPER

CONTROL

5120-080

GLASS RETENTION CLIPS

ACCESSORIES

5120-082

GLASS PLATE CLIP

9050-41

STONE SET

5120-085

FAÇADE RETENTION CLIP, TUDOR

9055-41

REAR STONE SET

5210-3050 TIE-ROD 17"

90-69500

VIEWING SCREEN

5300-066

PIEZO, ON/OFF BRACKET

90-57501

BLOWER

5532-095

HEAT EXCHANGER HINGE PLATE

5701-925H STARTER

COLLARS,

CHA/SAN

7211-238 TEK

BURNER

WARNING:

NOT

SUBSTITUTE

MATERIALS.

OR REPLACEMENT PARTS

OR FOR INFORMATION ABOUT PARTS OR SERVICE

CONTACT YOUR AUTHORIZED

EARTHSTONE RETAILER

OR THE NAME OF THE AUTHORIZED RETAILER NEAREST TO YOU

VISIT OUR WEBSITE

WWW

EARTHSTONESTOVES

COM

OR WRITE

EARTHSTONE

UALITY

OME

EATING

RODUCTS

317 Stafford Ave.
Morrisville, Vermont 05661-8695
E-Mail: inquiry@hearthstonestoves.com

Summary of Contents for Tribute DV 8050





































Search results

Summary of Contents for Tribute DV 8050

Reviews:

Related manuals for Tribute DV 8050

Brands by name

Popular brands

HearthStone Tribute DV 8050, Owner'S Manual & Installation Manual

Search results

Summary of Contents for Tribute DV 8050

Reviews:

Related manuals for Tribute DV 8050

Brands by name

Popular brands