Heat & Glo SL-36-Ultimate Owner'S Manual Download

Page: 45 / 55

Heat & Glo • SL-36-Ultimate • 2141-900 Rev. i • 5/11

Troubleshooting

With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do

experience a problem, this troubleshooting guide will assist a qualiﬁ ed service person in the diagnosis of a problem and the

corrective action to be taken. This troubleshooting guide can only be used by a qualiﬁ ed service technician.

A. Intelliﬁ re Ignition System

Symptom

Possible Cause

Corrective Action

1. The ignitor/module

makes noise, but no

spark.

a. Incorrect wiring.

Verify “S” wire (white) for sensor and “I” wire (orange) for ignitor

are connected to correct terminals on module and pilot assembly.

Reversed wires at the module may cause system to make sparking

noise, but spark may not be present at pilot hood.

b. Loose connections or electrical

shorts in the wiring.

Verify no loose connections or electrical shorts in wiring from mod-

ule to pilot assembly. Rod closest to pilot hood should be ignitor.

Verify connections underneath pilot assembly are tight; also verify

connections are not grounding out to metal chassis, pilot burner,

pilot enclosure, mesh screen if present, or any other metal object.

c. Ignitor gap is too large.

Verify gap of igniter to pilot hood. The gap should be approximately

.17 inch or 1/8 inch.

d. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

ignitor wire “I” from module. Place ON/OFF Rocker switch or wall

switch in ON position. Hold ground wire about 3/16 inch away from

“I” terminal on module. If there is no spark at “I” terminal module

must be replaced. If there is a spark at “I” terminal, module is ﬁ ne.

Inspect pilot assembly for shorted sparker wire or cracked insulator

around electrode.

2. Pilot won’t light,

there is no noise or

spark.

a. Transformer installed correctly.

Verify that transformer is installed and plugged into module. Check

voltage of transformer under load at spade connection on module

with ON/OFF switch in ON position. Acceptable readings of a good

transformer are between 3.2 and 2.8 volts AC.

b. A shorted or loose connection in wir-

ing conﬁ guration or wiring harness.

Remove and reinstall the wiring harness that plugs into module.

Verify there is a tight ﬁ t. Verify pilot assembly wiring to module.

Remove and verify continuity of each wire in wiring harness.

c. Improper wall switch wiring.

Verify that 110/VAC power is “ON” to junction box.

d. Module not grounded.

Verify black ground wire from module wire harness is grounded to

metal chassis of appliance.

e. Faulty module.

Turn ON/OFF rocker switch or wall switch to OFF position. Remove

ignitor wire “I” from module. Place ON/OFF Rocker switch or wall

switch in ON position. Hold ground wire about 3/16 inch away from

“I” terminal on module. If there is no spark at “I” terminal module

must be replaced. If there is a spark at “I” terminal, module is ﬁ ne.

Inspect pilot assembly for shorted sparker wire or cracked insulator

around electrode.

3. Pilot lights but con-

tinues to spark, and

main burner will not ig-

nite. (If the pilot contin-

ues to spark after the

pilot ﬂ ame has been lit,

ﬂ ame rectiﬁ cation has

not occurred.)

a. A shorted or loose connection in

sensor rod.

Verify all connections to wiring diagram in manual. Verify connec-

tions underneath pilot assembly are tight. Verify connections are

not grounding out to metal chassis, pilot burner, pilot enclosure or

screen if present, or any other metal object.

b. Poor ﬂ ame rectiﬁ cation or contami-

nated sensor rod.

Verify that ﬂ ame is engulﬁ ng sensor rod. If the pilot assembly does

not have a ground strap, consider installing one to increase ﬂ ame

rectiﬁ cation. Verify correct pilot oriﬁ ce is installed and inlet gas

speciﬁ cations. Flame carries rectiﬁ cation current, not the gas. If

ﬂ ame lifts from pilot hood, the circuit is broken. A wrong oriﬁ ce or

too high an inlet pressure can cause pilot ﬂ ame to lift. The sensor

rod may be contaminated. Clean sensor rod with emery cloth.

Summary of Contents for SL-36-Ultimate
























































Search results

Summary of Contents for SL-36-Ultimate

Reviews:

Related manuals for SL-36-Ultimate

Brands by name

Popular brands

Heat & Glo SL-36-Ultimate, Owner'S Manual

Search results

Summary of Contents for SL-36-Ultimate

Reviews:

Related manuals for SL-36-Ultimate

Brands by name

Popular brands