Retro-DWS Installation
2 of 12
Optional Accessories
HLA-120
General purpose 120V, plug-in thermostat (for GFC models)
GFA-STAT
NEMA 4X Ground Fault Protected Adjustable Thermostat
120V/240V 30amp (for CS models)
MA-10
GFCI/ELCI Electrical Equipment Protection Device
(for CS models)
TIMER-120P
120V plug-in timer (for GFC models)
TIMER-240P
240V plug-in timer (for GFC models)
TIMER-CS
120/240V hard wire timer (for CS models)
INSUL-FOIL
Aluminum reflective metalized foil bubble insulation
FOIL-TAPE
Professional Grade All Weather Foil Tape 2.83 inches x
150 feet (72mm x 46m)
INSUL-3.00
Polyethylene insulation sleeve for 3 inch ID pipe (6 feet
long, 3 1/2 inch ID, ¾ inch thick wall)
INSUL-4.00
Polyethylene insulation sleeve for 4 inch ID pipe (6 feet
long, 4 1/2 inch ID, 1 inch thick wall)
HLP-TAPE
Black wrap tape for sealing insulation ends together 2
inches x 100 feet (50.8mm x 3m)
TORQ-60
No hub torque wrench automatic release at 60 IN. LB.
WARRANTY
Extended 10 year limited product warranty
Ordering Chart
Example:
DWS – 5 – 100 – GFC
Cord-Set Type
GFC
Ground Fault Protected
CS
Cord Connected
(No GFCI)
Max length Max length
5 watt / 120 volt
230 ft 270 ft
8 watt / 120 volt
150 ft 200 ft
5 watt / 240 volt
460 ft 540 ft
8 watt / 240 volt
300 ft 400 ft
Length of Heater
Product
DWS
120 volt (100-130 volt) Retro-DWS
DWS2
240 volt (208-277 volt) Retro-DWS
Wattage
5
5 watts self-regulating heater (standard)
8
8 watts self-regulating heater
Retro-DWS | Product Code
Note
: Installers must
provide 20 Amp circuit for
Cord Set lengths greater
than maximum lengths set
for GFC
LEVIT
ON
WARNING
TO P
ROT
ECT
AG
AIN
ST
EL
ECT
RONIC
SH
OCK
TES
T
BEF
OR
E EA
CH USE
.
1. PL
UG
INT
O REC
EPT
ACL
E.
2. IF
LIGHT
IS NO
T ON,
P
RESS
AND REL
EA
SE
RE
SET
BUT
TON
- L
IGHT
SHOU
LD C
OM
E ON.
3. PRE
SS T
ES
T B
UT
TON -
LIGHT
MUS
T GO OF
F
4. PRESS
AND R
EL
EASE
RESET
BUT
TON
AGAIN
FO
R US
E.
DO NO
T USE IF
TES
T FAI
LS
RAINPR
OOF
DO NO
T IMMERSE
1L37
10
TES
T
TES
T
RESET
RES
ET
Cord-Set Version
Must be protected
with GFCI
(Ground Fault
Circuit Interrupter)
G
A
C
D
B
E
F
Kit Contents
Item Qty Description
A
1
Retro-DWS –Predetermined length (GFC shown)
B
1
Pre-drilled dissolving ballpoint
C
1
4" Flexible pipe coupler
D
1
4" x 3" Flexible pipe reducer
E
1
4" ABS Threaded male adapter SPIG X MIPT
F
1
3" ABS Threaded male adapter SPIG X MIPT
G
1
Optional Cord-Set (CS) power connection
Tools Required
• Standard screwdriver or nut driver
• Torque Wrench
• Pipe Cutting Tool for 4" and or 3" ABS
• Adjustable Wrench
Additional Materials Required
• Teflon tape or thread sealant
