Call 1-877-744-3649 for assistance or email us at service@phoenixinno.com
4
MC
OPERATING INSTRUCTIONS:
Using the Control Panel (See Fig. 3 Below):
Master Power Switch (A):
• Push button (A) to turn the appliance on. The fan will turn on and the indicator
lights (J) and (H) will turn on to indicate the unit is on.
Fan Button (B):
• This is a High and Low setting for the fan.
• The fan light area (H) denotes the Low fan setting and the fan light area (P)
denotes the High setting. As well the Temperature Digital Readout Screen
Heater Button (C):
• Push button ( C ) to turn the heater on. The indicator light (N) will indicate when the
heater is on. (The infrared heater will only turn on if the temperature setting is higher
than the room temperature.)
• Push button ( C ) again to turn the heater off.
Timer (E):
• If the timer is desired, push this button (E) , the indicator (O) will blink. The
time will show on the digital readout screen, push the button (F) the timer
will increase from “30-1H-2H-3H-4H-5H-6H-7H-8H-9H”, push the button
(G), the timer hours will decrease from “9H-8H-7H-6H-5H-4H-3H-2H-1H-30”
Note: The timer is approximate and extreme caution is necessary when the
heater is left operating and unattended. Keep children, invalids and pets away
from the unit when in use.
Temperature Buttons - Increase (F) and Decrease (G):
• This infrared heater is equipped with a thermostat. Before the
Temperature buttons will function, the Heater Button ( C ) must be pushed to
start the heater. Then, press the Temperature Button (F) to increase the
temperature. Press the Temperature Button (G) to decrease the temperature.
(The infrared heater will only turn on if the temperature setting is higher
than the room temperature.)
The Temperature Digital Readout Screen (K):
• This screen shows the current setting of the thermostat in default
Fahrenheit degrees.
• This screen will turn off after 5 minutes if there is no temperature
adjustments.
• The temperature light (L) indicates if the digital reading is in Fahrenheit
and the temperature light (M) indicates the digital reading is in Celcius
Oscillating Fan (D):
• Push the button (D). the indicator light (I) will turn on, the Oscillating Fan
will turn on.
• Push button (D) again, the Oscillating Fan will stop.
NOTE:
The fan will continue to work for several minutes when the heaters
turns off. This allows the infrared components inside the heater to cool down.
Using Remote Control (See Fig. 4 Below):
This appliance includes a remote control. To operate the appliance using the
remote control, ensure the unit is plugged in. Each remote control is shipped
with a plastic tab inserted into the battery chamber to prevent damage and
power loss. Pls remove by pulling on the tab out of the chamber. (See
Maintenance Section). See below for directions to use the remote control:
Celcius / Fahrenheit Setting Button (T):
• Push the button (T) to change the heat readout settings. The indicator
light (L) will indicate the reading is in Fahrenheit degrees and the indicator
light (M) will indicate Celsius degrees.
Temperature Buttons - Increase (U) and Decrease (V):
• This infrared heater is equipped with a thermostat. Before the Temperature
buttons will function, the Heater Button ( R ) must be pushed to start the heater.
Then, press the Temperature Button (U) to increase the temperature. Press the
Temperature Button (V) to decrease the temperature. (The infrared heater
will only turn on if the temperature setting is higher than the room temperature.)
Timer (S):
• If a timer is desired, push this button (S), the indicator (O) will blink, the time will
show on the digital readout screen, push the button (U) the timer hours will increase
from “30-1H-2H-3H-4H-5H-6H-7H-8H-9H” push the button (V), the timer hours will
decrease from “9H-8H-7H-6H-5H-4H-3H-2H-1H-30”.
Oscillating Fan (X):
• Push this button “X”, the indicator light “I” will turn on, the Oscillating Fan
will stop.
NOTE:
Direct the remote control at the appliance from 1 to 5 meter
distance for the remote control to function properly. The remote control
receptor is located in the control panel (Fig 1)
NOTE:
For remote control battery replacement, use Lithium Cell CR2025 3V.
NOTE:
This appliance comes equipped with an overheat protection safety device.
Should the appliance begin to overheat for any reason, it will automatically turn
all heater functions of the appliance` off. The appliance will have to be reset prior
to continuing use. To reset the overheat protection safety device, turn all controls
off and unplug the appliance. Wait 15 minutes, plug the appliance back in and
turn on. If the appliance continuously overheats, please call our customer service
department toll free at 1-877-744-3649 or email to service@phoenixinno.com.
WAVE
HEAT
Heater Button (R):
•
Push button (R) to turn the
heater on. The indicator
light (N) will indicate when
the heater is on. (The
infrared heater will only
turn on if the temperature
setting is higher than the
room temperature.)
Oscillating Fan (X):
•
Push the button (X) to
turn the oscillating feature
on and push the button (X)
again to turn the oscillating
feature off.
On/Off Button (Q):
•
Push button (Q) to turn
infrared heater on.
Fan Button (W):
•
This is a High and Low
setting for the fan and
the heater.
FIG. 4
Q
S
U
W
R
T
V
X
Fig. 3
72
A
B
C
D
E
F
G
H
I
J
K L M N
O
P
(K) will indicate "LO" and "HI".