background image

59

Heat & Glo  •  6000C-IPI, 8000C-IPI  •  2164-900 Rev. W  •  8/14

D.  Elevated Hearth Systems

Use the table below to identify the hearth system that will be used.  The table will also help identify effects on the various 
dimensions.  Some hearth systems will elevate the appliance off the 

fl

 oor at a given dimension.  For example, if appliance 

will be used with a Kenwood Cabinet with Base, the appliance will be elevated 9-1/4 in.  The 9-1/4 in. elevation will also 
have to be added to the following:  Wall penetration referenced in Figure 8.2 (Wall penetration) and Rough Opening Height 
(header height) referenced in Figure 5.2.  Note:  Finished 

fl

 oor thickness should also be considered when determining in-

stallation dimensions.

Note 1.  Add dimensions to Wall Penetration (Figure 8.2) and Rough Opening Height (Figure 5.2).
Note 2.  Verify Marble Cut Lengths on site prior to cutting.
Note 3.  Dimensions assume use of a 3/4 in. Hearth Pad.

MODEL

DESCRIPTION

PART #

ELEVATED APPLIANCE 

DIMENSION

 See Note 1

MARBLE LEG CUT 

LENGTH 

See Note 2

6000 
Series

KENWOOD CABINET 

KDC48DBP

0

33 in.

KENWOOD CABINET  W/ BASE 

KDC48DBP W/ HTKDC48DBP

9-1/4 in.

33 in.

KENWOOD CORNER CABINET

KDA48DBP

0

33 in.

KENWOOD CORNER CABINET  W/ BASE  KDA48DBP W/ HTKDA48DBP

9-1/4 in.

33 in.

KENWOOD MANTEL                     

AFKDMPB

0 (See Note 3)

33 in.

KENWOOD MANTEL W/ BASE 

AFKDMPB W/ HTKDMPB

9-1/4 in.

33 in.

LUNA SURROUND

LUNA-36-GY

1-1/16 in.

N/A

8000 
Series

KENWOOD MANTEL                    

AFKDMPC

0 (See Note 3)

32-7/8 in.

KENWOOD MANTEL W/ BASE

AFKDMPC W/ HTKDMPC

9-1/4 in.

32-7/8 in.

Summary of Contents for 6000C-IPI






















































































Reviews: