background image

                 OPERATION, SERVICE AND  
              MAINTENANCE

 

INSTRUCTION

   

 

3035443

                                                                                                        

MP5157

 

 

   
 

 

ANSI Z83.8 (2016) 

– CSA 2.6M (2016) Gas-Fired Duct Furnace 

 

                        

 

!

                   

                WARNING:

FIRE OR EXPLOSION HAZARD

Failure to follow safety warnings exactly could result in serious injury,    
death or property damage. 

Be sure to read and understand the installation, operation and service 
instructions in this manual.

Improper installation, adjustment, alteration, service or maintenance can 
cause serious injury, death or property damage.

Do not store or use gasoline or other flammable vapors and liquids in the   
vicinity of this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

· 

Do not try to light any appliance

· 

Do not touch any electrical switch; do not use any phone in your building

· 

Leave the building immediately

· 

Immediately call your gas supplier from a phone remote from the 
building. 

Follow the gas supplier’s instructions.

· 

If you cannot reach your gas supplier, call the fire department.

Installation must be performed by a qualified installer, service agency or gas 
supplier

.

 

 
 

 

This manual must be kept with the appliance for future reference. 

 
 

                              
 

 
Heatco Inc. 
50 Heatco Court 

 

 

 

 

 

 

 

 

 

Cartersville, GA 30120 

 

 

 

 

 

 

 

 

 

 

H(M,H)-USM-MAN-E-2016-12 

 

 

 

 

 

 

 

 

 

 

 

HM and HH SERIES 

DUCT FURNACE MODULE 

Summary of Contents for HH SERIES

















Reviews: