Heatcraft Refrigeration Products BEACON II H-IM-79E Installation And Operation Manual Download

Page: 23 / 36

InterLink Replacement Parts List

Table 3. InterLink Replacement Parts List

PART DESCRIPTION

PART NUMBER

Beacon II Control Board

28910101

*Temperature Sensor kit – White Leads

89904902

Transformers:

120/24 volt – 40 VA

22529601

240/24 volt – 40 VA

22529602

460/24 volt – 40 VA

22529603

575/24 volt – 40 VA

22529701

Pilot Relay

22511401

Contactor for Compressor 40 amp with 24 volt Coil

2252440

Terminal Block – Condensing Unit

2251266

Low Pressure Switch Time Delay Relay

22536801

Electric Expansion Valve

ESB 1 – 3/8” x 3/8” Conn

29320003

ESB 4 – 3/8” x 3/8” Conn

29320004

ESB 10 – 3/8” x 3/8” Conn

29320007

ESB 10 – 1/2” x 1/2” Conn

29320008

ESB 15 – 7/8” x 1 3/8” Conn

29320013

ESB 20 – 7/8” x 1 3/8” Conn

29320014

Expansion Valve Molded Connector

(Bipolar valves)

22515201

Pressure Transducer

28911201

Pressure Transducer Harness

22515101

Beacon II Smart Controller

89704301

**Smart Controller Software Package

89704101

Beacon II Communications Hub

89708001

*Only the sensor with white leads is shipped as a service replacement part
**Smart Controller Software package is sold separately

OPERATIONAL LIMITS

Voltage Range

18 VAC to 30 VAC

Controlling Box Temp. Range

-30

°F to 70°F

Temperature Differential

2°F

Cold Ambient Limits

Start & operate to -20°F

Table 4. Operational Limits

Commercial Refrigeration Parts

Replacement Parts by

InterLink is your link to a complete line of dependable and certified commercial refrigeration parts, accessories

and innovative electronic controls for all Heatcraft Refrigeration Products (HRP) brands - including Bohn, Larkin,

Climate Control and Chandler. At InterLink, we provide our wholesalers with a comprehensive selection of product

solutions and innovative technologies for the installed customer base. And every product is built to ensure the

same high performance standards with which all HRP brands are built — backed by a dedicated team to serve

every customer need, delivering at the best lead times in the industry.

Visit www.interlinkparts.com or call (800) 686-7278 for more information.

Summary of Contents for BEACON II H-IM-79E





































Search results

Summary of Contents for BEACON II H-IM-79E

Reviews:

Related manuals for BEACON II H-IM-79E

Brands by name

Popular brands

Heatcraft Refrigeration Products BEACON II H-IM-79E, Installation And Operation Manual

Search results

Summary of Contents for BEACON II H-IM-79E

Reviews:

Related manuals for BEACON II H-IM-79E

Brands by name

Popular brands