background image

13

PRO

3

 Top Mount Packaged Refrigeration System | Outdoor

Keypads

Preliminary Configurations

Once  the  electrical  connections  have  been  completed,  simply 
power-up the controller to make it operative.
Heatcraft  recommends  that  you  check  the  parameters  listed.

Functions Available from Keypad

ON AND OFF
Switching the instrument ON:
 press UP for more than 3 s (when 

pressing the button, the display shows ON).
Switching the instrument OFF: press UP for more than 3 s. The 

display shows the message “OFF”, alternating with the temperature 

measured by the set probe.
In off status, the following functions are disabled (if featured by the 

model):

•  compressor control / duty setting / continuous cycle;
•  defrost;
•  fan control;
•  alarms : ‘LO’, ‘HI’, ‘IA’, ‘cht’, ‘CHT’;
•  door switch (A4= 7/8 );
•  buzzer (when available)

While the following are enabled:

•  temperature display, alternating with the message “OFF”;
•  parameter display and setting;
•  alarms: “E0”, “E1”, “E2”;
•  the internal timer relating to parameter ‘dI’ is updated. If ‘dI’ 

expires in OFF status, a defrost is performed when restarting;

•  auxiliary relay management, only in the following 

configurations:

•  H1= = 1/2 (“E0” alarm only)
•  H1= 3, A4= 6;

BUT. NO.

NORMAL OPERATION

START UP

pressing 

the button 

alone

pressing 

with other 

buttons

1

more than 

3 s: switch 

ON/OFF

pressed 

together 

with 3 

activates/

deactivates 

the 

continuous 

cycle

2

- 1 s: 

displays/

sets the set 

point

- more 

than 3 s: 

accesses 

the 

parameter 

setting 

menu 
(enter 

password 

22)

- mutes the 

audible 

alarm 

(buzzer)

for 1 s 
RESET 

current EZY 

set

pressed 

together 
(2 and 3) 

activate 

parameter 

reset 

procedure

3

more 

than 3 s: 

activates/

deactivates 

the defrost

pressed 

together 

with 1 

activates/

deactivates 

the 

continuous 

cycle

for 1 s 

displays 

firmware 

version

Control Parameters

st

set point

rd

set point differential

Alarm Parameters

Ad

temperature alarm delay

AL

low temperature alarm threshold/deviation

AH

high temperature alarm threshold/deviation

Defrost Parameters

d0

type of defrost

dl

interval between two defrosts

dt

end defrost temperature

dP

maximum defrost duration

3.

 C

on

tr

ollers

Summary of Contents for PRO TOP MOUNT H-IM-82C



























Reviews: