background image

4

598-1324-01

SYMPTOM
Light  will  not 
come on.

Light comes on 
in daylight.

Light comes on 
for no apparent 
reason.

POSSIBLE CAUSE
1.  The halogen lamp is positioned too 

close to the light control’s sensor or 
pointed at nearby objects that cause 
heat to trigger the sensor 

(Reposition 

the  lamp  away  from  the  sensor  or 
nearby objects)

.

2.  Light control’s sensor is pointed toward 

a heat source like an air vent, dryer 
vent, or brightly-painted heat-reflective 
surface 

(Reposition sensor)

.

3.  On-time set too high 

(Reduce Time 

setting)

.

1.  Heat or light from the halogen lamp 

may  be  turning  the  light  control  on 
and  off 

(Reposition  the  lamp  away 

from the sensor)

.

2.  Heat  being  reflected  from  other 

objects  may  be  affecting  the  light 
control 

(Re-aim sensor)

.

3.  Light  control  is  in  the  TEST  mode 

and warming up 

(Flashing is normal 

under these conditions)

.

SYMPTOM
Light stays on 
continuously.

Light  flashes 
on and off.

POSSIBLE CAUSE
1.  Light switch is turned off.
2.  Halogen  lamp  is  loose  or  burned 

out.

3.  Fuse  is  blown  or  circuit  breaker  is 

turned off.

4.  Daylight turn-off is in effect 

(Recheck 

after dark)

.

5.  Incorrect circuit wiring, if this is a new 

installation.

6.  Not  aimed  correctly 

(Re-aim  the 

sensor to cover desired area)

.

1.  Light  control  may  be  installed  in  a 

relatively dark location.

2.  Light control is in TEST 

(Select 1, 5 

or 10 minutes for AUTO time)

.

1.  Light control’s sensor may be detect-

ing small animals, swaying trees, or 
automobile traffic 

(Re-aim sensor)

.

2.  Sensitivity is set too high 

(Reduce 

sensitivity)

.

TROUBLESHOOTING GUIDE

TWO YEAR LIMITED WARRANTY

This is a “Limited Warranty” which gives you specific legal rights. You may also have other rights which vary from state 
to state or province to province.
For a period of two years from the date of purchase, any malfunction caused by factory defective parts or workmanship 
will be corrected at no charge to you.
Not Covered - Repair service, adjustment and calibration due to misuse, abuse or negligence, light bulbs, batteries, 
and other expendable items are not covered by this warranty. Unauthorized service or modification of the product or of 
any furnished component will void this warranty in its entirety. This warranty does not include reimbursement for incon-
venience, installation, setup time, loss of use, unauthorized service, or return shipping charges.
This warranty covers only HeathCo LLC assembled products and is not extended to other equipment and components 
that a customer uses in conjunction with our products.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING ANY 
WARRANTY, REPRESENTATION OR CONDITION OF MERCHANT ABILITY OR THAT THE PRODUCTS ARE FIT FOR 
ANY PARTICULAR PURPOSE OR USE, AND SPECIFICALLY IN LIEU OF ALL SPECIAL, INDIRECT, INCIDENTAL, 
OR CONSEQUENTIAL DAMAGES.
REPAIR OR REPLACEMENT SHALL BE THE SOLE REMEDY OF THE CUSTOMER AND THERE SHALL BE NO 
LIABILITY ON THE PART OF HEATHCO LLC FOR ANY SPECIAL, INDIRECT, INCIDENTAL, OR CONSEQUENTIAL 
DAMAGES,  INCLUDING  BUT  NOT  LIMITED TO  ANY  LOSS  OF  BUSINESS  OR  PROFITS,  WHETHER  OR  NOT 
FORESEEABLE. Some states or provinces do not allow the exclusion or limitation of incidental or consequential dam-
ages, so the above limitation or exclusion may not apply to you. Please keep your dated sales receipt, it is required for 
all warranty requests.

TECHNICAL SERvICE

Please call 1-800-858-8501 (English speaking only) for assistance before returning 

product to store.

If you experience a problem, follow this guide. You may also want to visit our Web site at: 

www.hzsupport.com. 

If the problem persists, call* for assistance at 

1-800-858-8501 (English speaking only), 7:30 AM to 4:30 PM CST 

(M-F). You may also write* to:
HeathCo LLC, P.O. Box 90004, Bowling Green, KY 42102-9004
ATTN: Technical Service
* If contacting Technical Service, please have the following information available: Model Number, Date of Pur-
chase, and Place of Purchase.

No Service Parts Available for this Product

Summary of Contents for BL-5511













Reviews: