background image

28881 Rev G

22

01-02

NOVUS REAR DIRECT VENT

I.  DETERMINING THE IGNITION

To  determine  whether  your  appliance  is  an  electronic

ignition or a standing pilot ignition system, open the control

access panel to examine the wiring system. If your system

has a red ignitor button, as shown in Figure 39, you own a

standing pilot ignition appliance. If no red ignitor button is

present, you own an electronic ignition appliance.
You may also check the rating label located on the inside

of the control access panel to determine ignition type.

Figure 39

Standing Pilot Ignition

1. ELECTRONIC  IGNITION APPLIANCES

FOR YOUR SAFETY

READ BEFORE OPERATING

WARNING! If you do not follow these instructions exactly, a fire or explosion may result causing

property damage, personal injury or loss of life.

A. This  appliance  does  not  have  a  pilot.  It  is  equipped  with  an  ignition  device  which  automatically  lights  the

burner. Do not try to light the burner by hand.

B. BEFORE OPERATING smell all around the appliance area for gas. Be sure to smell next to the floor because

some gas is heavier than air and will settle on the floor.

WHAT TO DO IF YOU SMELL GAS

•

Do not try to light any appliance.

•

Do not touch any electric switch; do not use any phone in your building

•

Immediately  call  your  gas  supplier  from  a  neighbor’s  phone.  Follow  the  supplier’s  instructions.

•

If you cannot reach your gas supplier, call the fire department.

C. Use only your hand to push in and  turn the manual shutoff valve. Never use tools. If the manual shutoff valve

will not move by hand, don’t try to repair it - call a qualified service technician. Force or attempted repair may

result in a fire or explosion.

D. Do not use this appliance if any part has been under water. Immediately call a qualified service technician to

inspect the appliance and to replace any part of the control system and any gas control which has been under

water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above on this label.

2. Turn wall switch to the “OFF” position.

3. This  appliance  is  equipped  with  an  ignition  device  which  automatically  lights  the  burner.  Do  not  try  to  light

burner by hand.

4. Wait five (5) minutes to clear out any gas. If you then smell gas, STOP! Follow “B” in the safety information

above on this label. If you don’t smell gas, go on to the next step.

5. To turn on burner, turn on all electric power to this appliance.

6. If the appliance will not operate, follow the instructions “TO TURN OFF GAS TO APPLIANCE” and call your

service technician or gas supplier.

TO TURN OFF GAS TO APPLIANCE

1. Turn off the wall switch.

2. Turn gas line to the “OFF” position.

3. Close  control  access  panel.

J. LIGHTING INSTRUCTIONS

All manuals and user guides at all-guides.com

Summary of Contents for NOVUS series

































Reviews: