background image

SnowMeltz® Warranty

Heatizon Systems warrants SnowMeltz® to be free from defects 

in material and workmanship for a period of  ten (10) years and 

Activation Device(s) for a period of one (1) year.  Such warranty 

periods shall commence on the date of shipment by Heatizon 

Systems.  If any parts are found to be defective in manufacture during such time period,  Heatizon 

Systems will, at its sole option, replace or repair defective parts.   

This Limited Warranty applies only if articles sold hereunder (a) are selected, designed, and installed according 

to instruction and operation manuals furnished by Heatizon Systems and installed in a “workmanlike manner” 

according to the building association standards adopted by Heatizon Systems, (b) remain in their originally 

installed location, (c) are connected to proper power supplies, (d) are not misused or abused, (e) show no 

evidence of tampering, mishandling, neglect, damage (accidental or otherwise), modifications or repair without 

the approval of Heatizon Systems, or damage done to the product by anyone other than Heatizon Systems, 

and (f) are installed in accordance with applicable code requirements.  Any warranty claims must be made in 

writing, no later than one (1) month following expiration of the warranty period, and must be accompanied 

by the warranted part or component.  Any claim not made in such manner shall not be honored by Heatizon 

Systems.

This Limited Warranty does not cover:

1.  The workmanship of any installer of Heatizon Systems radiant panel or cable heating products.

2.  Any Heatizon Systems radiant heating products that have a failure or malfunction resulting from improper or negligent 

operation, installation, accident, abuse, misuse, unauthorized alteration or improper repair or maintenance.

3.  Any Heatizon Systems radiant heating products that have had components not purchased from Heatizon Systems 

integrated into or connected to them.

4.  Any labor costs for removal of alleged defective part(s) and/or reinstallation of replacement part(s), transportation to 

and from Heatizon Systems (if necessary) and any other material necessary to perform the exchange or repair.

5.  Any Heatizon Systems heating products that have not been properly registered by completion and return of the 

Warranty Registration Card attached hereto within ninety (90) days of the date of sale.

DISCLAIMER OF WARRANTIES:

 

This warranty described above is in lieu of all other warranties, express or implied, including but not 

limited to any implied warranties of fitness for a particular purpose and merchantability.  Heatizon Systems 

expressly disclaims and excludes any liability for losses, expenses, inconveniences, consequential, incidental, 

indirect, or punitive damages for breach of any express or implied warranty.  By installing and/or purchasing 

Heatizon Systems products, you accept the terms of this limited warranty.

 

Some states do not allow the exclusion or limitation of incidental or consequential damages, or 

limitations on how long an implied warranty lasts, so the above limitations and exclusions may not apply to 

you.  This Limited Warranty gives you specific legal rights, and you may also have other rights which may vary 

from state to state. 

HEATIZON SYSTEMS DISCLAIMS ANY WARRANTY NOT PROVIDED HEREIN INCLUDING THE IMPLIED WARRANTY OF 

MERCHANTIBILITY AND IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. HEATIZON SYSTEMS FURTHER 

DISCLAIMS ANY RESPONSIBILITY FOR LOSSES, EXPENSES, INCONVENIENCES, SPECIAL, INDIRECT, SECONDARY, 

INCIDENTAL, OR CONSEQUENTIAL DAMAGES ARISING FROM OWNERSHIP OR USE OF THE PRODUCT. THERE ARE NO 

WARRANTIES THAT EXTEND BEYOND THE FACE HEREOF.

Heatizon Systems

4137 South 500 West

Murray, UT 84123

Phone (801) 293-1232 Fax (801) 293-3077

heatizon.com

From Heatizon Systems

4137 South 500 West

Murray, Utah 84123

888-239-1232 | heatizon.com

Summary of Contents for SnoWmeltz































Reviews: