Heatworks MODEL 3 User Manual & Installation Manual Download

Page: 31 / 38

www.myheatworks.com

| 31

•

If there is any disassembling of any components; or

•

The water heater is subjected to applications of DC voltage; or

•

The water heater is operated without inlet filter screen located inside the water inlet; or

•

The water heater installation exposes the unit to the elements; or

•

The workmanship of any installer; or

•

The spray head is not regularly descaled.

4. Owner, and not Manufacturer or its agent / representative, is liable for and shall pay for all field

charges for labor or other expenses incurred in the removal or any

NON-COVERED WARRANTY

expense incurred by Owner. Manufacturer reserves the right to deny warranty coverage upon

Manufacturer’s examination of unit.

WHAT WILL VOID YOUR LIMITED WARRANTY

1. The unit is tampered with or self-serviced in anyway.

2. The unit is installed outdoors, without adequate protection from the elements.

3. The unit is installed in an orientation other than specified in this manual.

4. The unit is used with any liquids other than potable water.

5. More than 10% glycol is used with a radiant heating application.

6. The unit is used with any unapproved chemicals.

7. Components/accessories not compatible with or not intended for the unit are used.

8. This unit is used in an unapproved scenario such as, but not limited to, a fish tank water heater,

to heat pools or spas, with a non-compatible AC/DC converter, if undersized for the intended

application, etc.

9. The COLD | INLET or HOT | OUTLET is connected to any tap or fitting other than those

specified.

10. The unit is sold through an unauthorized third party by original Owner.

APPLICABLE LAW

This limited warranty shall be governed by the laws of the State of South Carolina.

RETURN POLICY

If, within (14) days of purchase (or for pre-order units date of shipment) and prior to installation,

the Owner finds that the purchased unit is not suitable for their demands, Owner must contact

support at

info@heatworks.tech

or call 888-506-2821 in order to receive a return authorization

form for the product. Returns will not be accepted without a return authorization number issued

by Heatworks. Return shipping is the responsibility of the customer, and all returned products

must be wrapped and packaged securely to avoid shipping damage. All products must be returned

Summary of Contents for MODEL 3







































Search results

Summary of Contents for MODEL 3

Reviews:

Related manuals for MODEL 3

Brands by name

Popular brands

Heatworks MODEL 3, User Manual & Installation Manual

Search results

Summary of Contents for MODEL 3

Reviews:

Related manuals for MODEL 3

Brands by name

Popular brands