C
C
C
C
A
A
A
A
L
L
L
L
II
II
B
B
B
B
R
R
R
R
A
A
A
A
T
T
T
T
II
II
O
O
O
O
N
N
N
N
P
P
P
P
R
R
R
R
O
O
O
O
C
C
C
C
E
E
E
E
D
D
D
D
U
U
U
U
R
R
R
R
E
E
E
E
WARNING: DURING THE ENTIRE CALIBRATION PROCESS, STAND ON THE PLASTIC SIDE RAILS
ONLY! DO NOT STAND ON TREADMILL WALKING BELT!
MODEL 2600
1.
With the safety pull pin inserted, plug the power cord into the wall socket.
2.
Immediately after plugging in the power cord, while the display windows are reading “88888,” press the
INCLINE-UP and INCLINE-DOWN buttons simultaneously. This should enter you into the calibration
mode.
3.
When you enter the calibration mode, there will be some parameters in the window displays. For the
English setting (MPH), the display should have a “10.0”in the speed window, and “En=y” in the time
window, and a “15” in the incline window.
4.
To change to metric (KPH), just after step 2 is completed, press the POWER button once and the display
should read “16.0” in the speed window, an “En=n” in the window, and a “15” in the incline window.
5.
To adjust the max. speed setting (whether you are in English or metric) use the SPEED-UP and
SPEED-DOWN buttons to achieve desired setting. “10.0” is standard for English and “16.0” is standard
for metric.
6.
To adjust the incline readout, use the INCLINE-UP and the INCLINE-DOWN buttons to achieve desired
setting. “15” is standard.
7.
When parameters are set
(DO NOT STAND ON TREADMILL BELT)
, press the START/PAUSE button to
begin the calibration process. “Cal” will appear in the calories window. The treadmill will automatically
set the low speed and high speed and will also set the incline from top to bottom.
8.
When the calibration process is finished, the “Cal” displayed in the distance window will begin flashing
(also the walking belt will begin moving again). While the “Cal” is flashing, press any button to end the
calibration process.
9.
Your treadmill is now ready to use.
Calibrate the elevation.
1.
Plug treadmill into wall outlet.
2.
Depress and hold, PROGRAM INTERVAL, SPEED DOWN, POWER.
3.
Release SPEED DOWN. Hear a beep? If not, repeat the above step.
4.
Release POWER and PROGRAM INTERVAL.
5.
Press POWER. The treadmill will raise itself to the highest elevation.
6.
Press PROGRAM INTERVAL. The treadmill will go to the lowest position.
7.
Press PROGRAM INTERVAL. The calibration is complete.
Calibrate the speed.
1.
Plug treadmill into wall outlet. Straddle the treadmill belt.
2.
Depress and hold, PROGRAM INTERVAL, SPEED DOWN, POWER.
3.
Release SPEED DOWN. Hear a beep? If not, repeat the above step.
4.
Release POWER AND PROGRAM INTERVAL.
5.
Press START/PAUSE. The belt should begin to move at the minimum speed setting. Use the SPEED UP
and SPEED DOWN buttons to set the minimum speed at .5 mph. After this is done, press POWER.
6.
The belt will rapidly move to the maximum speed setting. Use the SPEED UP and SPEED DOWN buttons
to set the maximum speed at 10.0 mph (model 3600) or 11.0 mph (model 4600). After this is done, press
POWER.
7.
The belt will somewhat slow down. Use the SPEED UP and SPEED DOWN buttons to set the actual
speed displayed in the SPEED window with the desired speed in the CALORIES window. When the two
speeds are equal, press POWER. The calibration is complete.
MODEL 3600, 4600
HEBB
Industries, Inc.
Manufacturers of Fitness Equipment
20