hebvest
.
com
t 800.469.8908
|
f 407.264.6309
|
mike@hebvest
.
com
Commercial 3HP Blender with 64oz. Container
cleaning
guide
Warning: Unplug the power cord to ensure safety
user
guide
Warning: Unplug the power cord to ensure safety
important
safeguards
Read all instructions
1. Place a little warm water with a small amount of detergent into the jug. Attach lid and switch blender on for
approximately 10 seconds. This will remove almost all residue. Empty jug, rinse, and leave upturned to dry. Do
not clean inside of jug by hand unless cutting unit has been removed.
2. To remove or replace blade assembly, simply turn the retaining ring at the bottom of the jug counter-clockwise.
3. To clean motor base, use a slightly damp cloth only. Never immerse motor base in water.
4. To extend the lifespan of the cutting unit, please do not immerse the jug in water or leave water in the jug for
a long period of time. Following this precaution will help to prevent rusting of the ball bearing by reducing its
potential contact with water to a minimum.
1. This blender is fitted with a safety overload switch at the bottom of the machine. If the motor overloads, the
power will be automatically cut to ensure safety. Please check and remove unsuitable blending ingredients,
then press the reset button (on the bottom) to start again.
2. Ensure that the power cord is correctly connected to the blender.
3. If the blender still does not function correctly, contact and consult your nearest distributor and refer to the
warranty card. Do not attempt to disassemble and repair it on your own.
4. If the power cord is damaged, it must be replaced or repaired by a qualified electrician or engineer to avoid
hazard.
5. After long-term use, the cutting unit will wear down and require replacement. Contact your store of purchase,
nearest distributor, or one of our after-service centers.
Warning: Blades are sharp. Handle carefully.
• To protect against risk of electric shock, do not place blender base or power supply cord in water or in any
other liquid.
• Close supervision is necessary when the appliance is used by or near children.
• Unplug from outlet prior to assembling or cleaning the appliance.
• Avoid touching moving parts.
• Do not operate the appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped
or damaged in any manner.
• Return appliance to the nearest authorized service facility for examination, repair, or electrical or mechanical
adjustment.
• Do not use outdoors. This appliance is for indoor use only.
• Do not let cord hang over the edge of the table or counter.
• Keep hands and utensils out of the jug while operating to reduce risk of severe injury or damage. A scraper
may be used only when the blender is OFF.
• Blades are sharp. Handle carefully.
• To reduce the risk of injury, never place cutting blade assembly on base without ensuring the jug is properly
attached; never remove the jug during operation.
• Only operate the blender with the lid in place.
• The manufacturer does not recommended use of attachments, including canning jugs, because these may
cause injury.
• Jug should not be more than 2/3 full when blending or when mixing rod is left in place. Mixing rod (tamper tool)
must
ONLY
be used through the hole in the lid when blender is in operation.
• Over-processing will cause the mixture to overheat.
• Ensure the blender is on a flat, level, stable and dry surface prior to operation.
• Always ensure that the jug is properly sealed in position and the jug lid is properly fitted and secured before
switching on the blender.
• When blending hot liquids: remove center piece (LID INSERT) of the two-piece cover to allow steam to escape.
Always start the motor on
LO
speed and increase to
HI
speed if necessary.
• Ensure that the lid is located under raised projections on the jug before switching on. The lid can only be
removed when the blender is
OFF
and the cutting unit has ceased turning.
• Never leave the blender unattended when in use.
