H E D L E R S y s t e m l i c h t G m b H H e e r s t r a s s e 1 1 2 D - 6 5 5 9 4 R u n k e l / L a h n w w w . h e d l e r. c o m
Te l e f o n + 4 9 - ( 0 ) 6 4 8 2 9 1 8 1 0 0 Te l e f a x + 4 9 - ( 0 ) 6 4 8 2 9 1 8 1 1 1 e M a i l i n f o @ h e d l e r. c o m
Profilux
®
LED
1400
/ Profilux
®
LED
1400
DMX
Service
A blinking of this LED indicates that the HEDLER Profilux
®
LED
1400
light unit model was in operation for 6000 hours. The light unit should be send
to HEDLER Systemlicht GmbH for recalibration. Please contact HEDLER Systemlicht GmbH directly or contact your photographic specialized
dealer.
0049 (0)6482-918100
info@hedler.com
Power
A continuous glowing of this LED indicates the light unit is switched on.
Cooling
A continuous glowing of this LED indicates the fan cooling is functional.
LED
The light units of the HEDLER Profilux
®
LED range are equipped with one 185 W high power single cell LED with 138 lm/W, which can´t be
replaced by the user. If any technical failure of the LED takes place please contact HEDLER Systemlicht GmbH or your photographic specialized
dealer.
0049 (0)6482-918100
info@hedler.com
FRESNEL LENS
To replace the Fresnel lens: please, make sure that the housing of the HEDLER Profilux
®
LED
1400
/ HEDLER Profilux
®
LED
1400
DMX has cooled off
before interchanging the Fresnel lens, otherwise there is a risk of burning! Always disconnect the HEDLER Profilux
®
LED
1400
/ HEDLER Profilux
®
LED
1400
DMX from the power supply before interchanging the Fresnel lens. Unscrew the four socket screws of the housings front plate and
remove the front plate with the Fresnel lens. Unscrew the securing screws of the Fresnel lens and replace the defective one with an original
HEDLER Fresnel lens only. After replacing the Fresnel lens tighten its securing screws hand-tight. Attach the front plate at the housing and tighten
the front plates four securing screws. Please, before taking the HEDLER Profilux
®
LED
1400
/ HEDLER Profilux
®
LED
1400
DMX in operation, make
sure that the front plate is mounted correctly!
FOCUSING
To focus the HEDLER Profilux
®
LED
1400
or the HEDLER Profilux
®
LED
1400
DMX light beam turn the focusing knob anti clock-wise (increased
spotlight characteristic) or clock-wise (increased floodlight characteristic) to adjust the light beams size.
DMX
At the back of the HEDLER Profilux
®
LED
1400
DMX light unit there are two 5-pin DMX-sockets with standard pin configuration. Connected
to a suitable DMX controller the light units can be switched on / off and the light output power can be adjusted remotely. The upper DMX
connect is used for the forementioned operations of the light unit. The lower DMX connect is used to connect another light unit and works as a
„passthrough feature“ for the DMX-signal. Setting the DMX-address of the respectively light unit is done directly at the light unit, no additional
accessory is needed.
Setting the DMX-address will be done as follows: a) HEDLER Profilux
®
LED
1400
DMX must be connected to a power supply and switched off;
b) press the key button Dimmer OFF / ON for approx. 3 seconds or until „A--“ is displayed and don´t release the key button; c) pressing the
key button Fan 100% / Automatic or POWER OFF / ON once the numerical address of the light unit will be increased / decreased by one; d) to
quit the process release the key button Dimmer OFF / ON.
DMX-pin configuration of the HEDLER Profilux
®
LED
1400
DMX (front view)
HEDLER
®
S y s t e m l i c h t
OPERATION MANUAL
5 pin XLR plug
1 - earth/shielding
2 - DMX-
3 - DMX+
4 - optional 2nd bus system - DMX-
5 - optional 2nd bus system - DMX+
5 pin XLR socket
1 - earth/shielding
2 - DMX-
3 - DMX+
4 - optional 2nd bus system - DMX-
5 - optional 2nd bus system - DMX+
