background image

 

 

 

                                                                                                             

ROTARY HAMMER 

RECYCLING 

 
Electrical and electronic equipment waste (WEEE) might contain dangerous materials which 
can have a negative impact on the environment and human health if not collected separately. 
This item is in conformity with the European Directive EU WEEE (2012/19/EU) and is marked 
with an electronic and electrical waste logo graphically represented in the image below. 
      

This icon shows that WEEE should not be collected with household waste but 
separately. 
We recommend you to consider the following: 

       - Materials and components used when manufacturing this item are high quality materials 
which can be reused and recycled; 
       - Do not throw away the item with household waste at the end of life; 
      -  Take the item to a collecting point where it will be collected for free;              
      -  Please contact the local authorities for details on the collecting centers.  
Conformity with the RoHS Directive: the item you purchased is in conformity with the EU 
Directive RoHS (2011/65/UE). It does not contain materials listed as harmful or prohibited in 
the Directive. 
Thank you for helping us protect the environment and our health! 
 

 

 

 

 

Manufactured for 

Network One Distribution 

Marcel Iancu St., no. 3-5, Bucharest, 020757 

2018 

 

 

Summary of Contents for VCRP001















Reviews: