background image

4.0 SAFETY REGULATIONS

5.0 REMOTE CONTROLLER

1- Keep all small parts out of the reach of children to prevent accidents.

2- The VR-Racer is a powerful machine.  You must move the left joystick slowly (the accelerator 

joystick) to ensure that it does not climb rapidly and cause a collision.  

3- When you hav

e finished flying, please 

remove the Li-Po battery from the VR-Racer. Before you

do, switch off the transmitter. 

4- Do not expose the battery t

o high 

temperatures or sources of hea

t (fi

re

, direct sunlight, etc). 

 

5- Bear in mind that the VR-Racer mus

t be fl

own at least 2-3 metres from the operator or from any 

other person that happens to be in the vicinity

to ensure that it cannot hit an

ybody in  the head, 

face 

or body.  

6- If childr

en fly the ai

rcraft they must be under the supervision of an adult a

t all times, who shall 

ensure that it is under contr

ol and within the field of vis

ion

, so th

at it can be handled easily.  

7- Look for an open space that complies with relevant r

egul

a

tions, with no t

r

ees, buildings and

/or 

other obstacles.

8- Nev

er fly the ai

rcr

aft near airports, 

railway lines or roads. 

9- Keep at a safe distance from pot

entially dange

rous areas and from specially-protected areas.  

10- Please respect relevant r

egul

ations r

ega

r

ding the 

recy

cling of electrical

/electronic materials and 

c

omponents when disposing of d

evices of this kind (transmitt

ers, cha

r

gers, models, e

tc.). Please take 

them to a recy

cling 

centre to dispose of them. 

12- Remove the transmitter batteries if you ar

e not going 

to use it for several days.  

13- Do not touch the mot

or during or immedi

ately aft

er flight as it 

could result in burns. 

14-  If you replace your VR-Racer  rotors ensure that y

ou fit them 

correctly. 

15- Do not throw any part of this product in the bin. All of its component parts must be taken to the 

nearest recy

cling 

centre for disposal. 

16- Not recommended f

or persons under the age of 12 

years. If used by childr

en, th

ey must be under 

the supervision of an adult at all times.

Specific

ations:

Signal type: 2.4 GHz.

Batteries required for the transmitter: 4 x 1.5V “AAA” si

z

e batteries (included).

Range: 40

-70 metres.

Movement channels: 4

11- If the VR-Racer suffers an impact that results in any altera

tion of it’s flight characteristics, please 

stop usin

g

 it immediately.

Summary of Contents for H817













Reviews: