#
GETTING STARTED...
#
CHARGING THE BATTERY...
#
FEATURES OF THE DOMINUS 10SC...
3
1/10th SCALE 4x4 SHORT
COURSE ELECTRIC TRUCK
1. Remove body and ba
Ʃ
ery from vehicle to prepare for charging
a. Read charging instruc
Ɵ
ons and understand all warnings and cau
Ɵ
ons before proceeding.
This product is not a
toy and should not be charged, operated, or maintained without supervision of an adult
b. Now is a good
Ɵ
me to start charging so you can be up and running as soon as possible but remember to return
to this guide in the presence of the charging ba
Ʃ
ery, remembering never to leave the ba
Ʃ
ery una
Ʃ
ended
while charging
2. Install the [6] AA type alkaline ba
Ʃ
eries into the transmi
Ʃ
er
3. Install the fully charged ba
Ʃ
ery into the vehicle, be sure to install the pins into the holes in the ba
Ʃ
ery moun
Ɵ
ng
posts
4. Ensure the motor is plugged into the receiver
5. Ensure the switch is in the OFF posi
Ɵ
on and connect the ba
Ʃ
ery to the ESC
6. Read and understand transmi
Ʃ
er cau
Ɵ
ons and se
ƫ
ng instruc
Ɵ
ons before use
a. Con
rm se
ƫ
ngs for steering and thro
Ʃ
le trim
7. Install body with 4 supplied clips; turn your equipment ON (radio
rst!) and enjoy!
• Steel ring and pinion type four wheel drive drivetrain
• Waterproof ESC and Servo
• Water Resistant receiver box
• HRS-3 2.4 GHz 3-Channel radio system
• 1,800 mAh 8.4V 7 Cell NiMH rechargeable ba
Ʃ
ery
pack with Tamiya-style plug
• Four wheel independent suspension
• Planetary metal gear di
ī
eren
Ɵ
als
• Ball bearing supported drivetrain
• Adjustable, oil
lled, coil-over shock absorbers with
bladders
• Adjustable suspension, camber, and front toe
• Pivot ball style front suspension with upper arm
• Stamped aluminum hinge pin braces
• Dual bell crank steering with servo saver
• Aluminum center drive sha
Ō
• Dual posi
Ɵ
on ba
Ʃ
ery strap, 6-7 cell con
gura
Ɵ
on
• Hex drive wheels, 26mm o
ī
set, compa
Ɵ
ble with
24mm (TRX)
• All-terrain square lug
Ɵ
res and stepped wheels
• Authen
Ɵ
c short course style body with spoiler
• Adjustable body mounts
• 550 21T brushed motor with 14T 32P pinion gear
Never leave the battery unattended while charging and never operate the charger without adult supervision
Never charge a warm battery, always allow the battery to cool to room temperature before charging
Never drop the charger or battery and do not attempt to charge a damaged battery
Inspect the battery and charger before use. Never use a battery or charger if the wire or connector has been
damaged or if the battery has experienced a short
Incorrect use of the battery, connections, or charging equipment can cause personal injury or property damage
Never allow batteries or charger to come in contact with moisture at any time
Stop charging immediately if the battery or charger becomes hot or changes form during use
NOTE: Only use chargers designed for use with NiMH ba
Ʃ
eries for the RC industry, using the supplied connector. Use
of other (non-RC speci
c) chargers or connectors can permanently damage the ba
Ʃ
ery and/or connected equipment.
Genuine NiMH replacement ba
Ʃ
eries are available at your local HobbyTown USA®.
1. Plug the charger into a properly grounded standard US wall plug
2. Plug the ba
Ʃ
ery into the charger and place the ba
Ʃ
ery on/in a non-
ammable surface/container and away from
any
ammable objects
3. A fully discharged ba
Ʃ
ery should charge in approximately 4-5 hours
a. Cau
Ɵ
on: Periodically monitor the temperature of the ba
Ʃ
ery while charging, if the temperature exceeds
115°F (45°C), disconnect the ba
Ʃ
ery from the charger and allow it to cool before reconnec
Ɵ
ng
4. Unplug the ba
Ʃ
ery from the charger when the ba
Ʃ
ery is slightly warm to the touch, indica
Ɵ
ng the ba
Ʃ
ery had been
fully charged
a. NOTE: Using a peak detec
Ɵ
on charger is recommended and will provide you with a faster and be
Ʃ
er charging
experience. We recommend the Primal Mul
Ɵ
-Chemistry charger by Radient RC.
b. Warning: Never charge the included ba
Ʃ
ery at a charge current exceeding 2.5A
5. Remove charger from wall plug
