#
HRS-3 CONFIGURATION CONTINUED...
7
1/10th SCALE 4x4 SHORT
COURSE ELECTRIC TRUCK
WORK AND OVER-HEAT.
› Steering-Le
Ō
Side Adjustment:
»
Turn the steering wheel completely to the le
Ō
and use the “ST+” or “ST-“ bu
Ʃ
ons to adjust the steering angle
to the desired loca
Ɵ
on.
› Steering-Right Side Adjustment:
»
Turn the steering wheel completely to the right and use the “ST+” or “ST-“ bu
Ʃ
ons to adjust the steering
angle to the desired loca
Ɵ
on.
• Thro
Ʃ
le and Brake End Point Adjustment (EPA)
› Use this func
Ɵ
on to adjust thro
Ʃ
le and brake travel adjustments.
› Thro
Ʃ
le Adjustment:
»
Pull the thro
Ʃ
le trigger completely to full thro
Ʃ
le and use the “TH+” or “TH-“ bu
Ʃ
ons to adjust the thro
Ʃ
le
end point to the desired loca
Ɵ
on.
› Brake Adjustment:
»
Push the trigger completely to the full brake and use the “TH+” or “TH-“ to adjust the brake end point ac-
cordingly.
Power Alarm:
• Idle and Low-Ba
Ʃ
ery Alarm
› When the steering wheel, thro
Ʃ
le trigger, or any bu
Ʃ
on is not operated for 10 minutes while the transmi
Ʃ
er is
on, a slow beeping alarm will sound to indicate that there has been no ac
Ɵ
on and the power should be turned
o
ī
.
• Low Ba
Ʃ
ery Voltage Alarm
› If the transmi
Ʃ
er ba
Ʃ
ery voltage drops to 6.7V or less, a slow beeping alarm sounds and the power LED light will
blink.
Ba
Ʃ
ery Replacement:
WARNING: Do not a
Ʃ
empt to charge non-rechargeable ba
Ʃ
eries
NOTE: Load the six AA ba
Ʃ
eries in accordance with the polarity marking on the ba
Ʃ
ery holder.
1. Remove the ba
Ʃ
ery cover from the transmi
Ʃ
er
2. Remove the old ba
Ʃ
eries
a. NOTE: Never mix brands or old/new ba
Ʃ
eries
b. Always be sure to be responsible and protect the environment when disposing ba
Ʃ
eries. Your local Hobby-
Town USA® dealer provides a FREE ba
Ʃ
ery disposal service
3. Insert the six new AA ba
Ʃ
eries according to the polarity markings on the ba
Ʃ
ery holder
a. If using rechargeable ba
Ʃ
eries, be sure to follow the manufacturer’s care and use instruc
Ɵ
ons
b. Rechargeable ba
Ʃ
eries must be removed from transmi
Ʃ
er before charging
4. Replace the ba
Ʃ
ery cover
5. Slide the Power switch to the ON posi
Ɵ
on. If the voltage is low, the low ba
Ʃ
ery alarm will sound. If the low ba
Ʃ
ery
alarm sounds, check that the ba
Ʃ
eries are properly inserted and are making su
ĸ
cient contact.
a. Low Ba
Ʃ
ery Alarm
i. An alarm will sound if the transmi
Ʃ
er voltage drops below 6.7V. This alarm is meant as a safety feature
only. The transmi
Ʃ
er should not be operated below 6.7V. If the low ba
Ʃ
ery alarm sounds, stop using
your model immediately and turn o
ī
both the model’s receiver and the transmi
Ʃ
er. Replace the trans-
mi
Ʃ
er ba
Ʃ
eries immediately with fresh AA ba
Ʃ
eries to prevent loss of control of your model
b. Always check the voltage of the transmi
Ʃ
er before use.
6. Always be sure to insert the ba
Ʃ
eries correctly according to the polarity markings, or the transmi
Ʃ
er may be dam-
aged.
7. When the transmi
Ʃ
er will not be used for a long period of
Ɵ
me, remove the ba
Ʃ
eries to prevent leaks and corro-
sion.
Se
ƫ
ng the ESC:
The ESC in your Dominus 10SC is pre-programmed to work best with the HRS-3 radio system. Use with another radio
system will not provide consistent performance and is not recommended.
