...IKONNIK XENON HRS3.2 CONFIGURATION CONTINUED
7
1/10th SCALE 2WD
MONSTER TRUCK
to the desired location.
• Throttle and Brake End Point Adjustment (EPA)
› Use this function to adjust throttle and brake travel adjustments.
› Throttle Adjustment:
» Pull the throttle trigger completely to full throttle and use the “TH+” or “TH-“ buttons to adjust the throttle end
point to the desired location.
› Brake Adjustment:
» Push the trigger forward to full brake and use the “TH+” or “TH-“ to adjust the brake end point accordingly.
Beginner Mode and Feature Lock Out:
Your transmitter is equipped with both a beginner mode and feature lock out. To avoid accidental changing of radio set-
tings by inexperienced or younger users, you can set the Beginner Mode switch to the middle position which will lock out
all functions except the steering trim. Moving the switch all the way to the right (when looking from the wheel of the trans-
mitter, will activate the Beginner Mode which is optimized to help users get used to the controls of their vehciles. When
activated, this beginner mode reduces the throttle output of the transmitter to reduce the overall speed of the vehicle,
while leaving all other functions fully operational.
Factory Reset
• The transmitter has a two stage factory reset.
› Model Reset: Resets the settings .
» Use a small toothpick to press the Reset button (above the LED) and power ON the Transmitter.
» Continue holding for 5 seconds until you hear a beep sound, then release the button.
› Factory Reset: resets all pareameters to the factory settings.
» Use a small toothpick to press the Reset button (above the LED) and power ON the Transmitter.
» Continue holding for 10 seconds until you hear 2 beep sounds, then release the button. Note: you will hear the
model reset single beep at 5 seconds, keep holding until you hear the 2 beeps to complete the reset.
Power Alarm:
• Idle and Low-Battery Alarm
› When the steering wheel, throttle trigger, or any button is not operated for 10 minutes while the transmitter is on,
a slow beeping alarm will sound to indicate that there has been no action and the power should be turned off and
back on to reset the transmitter alarm.
• Low Battery Voltage Alarm
› If the transmitter battery voltage drops to 4.5V or less, a slow beeping alarm sounds and the power LED light will
blink.
Battery Replacement:
WARNING: Do not attempt to charge non-rechargeable batteries
NOTE: Load the four AA batteries in accordance with the polarity marking on the battery holder.
1. Remove the battery cover from the transmitter
2. Remove the old batteries
a. NOTE: Never mix brands or old/new batteries.
b. Always be sure to be responsible and protect the environment when disposing batteries. Most local hobby dealers
provide a FREE battery disposal service.
3. Insert the four new AA batteries according to the polarity markings on the battery holder.
a. If using rechargeable batteries, be sure to follow the manufacturer’s care and use instructions.
b. Rechargeable batteries must be removed from transmitter before charging.
4. Replace the battery cover.
5. Slide the Power switch to the ON position. If the voltage is low, the low battery alarm will sound. If the low battery
alarm sounds, check that the batteries are properly inserted and are making sufficient contact.
a. Low Battery Alarm.
i. An alarm will sound if the transmitter voltage drops below 4.5V. This alarm is meant as a safety feature only.
The transmitter should not be operated below 4.5V. If the low battery alarm sounds, stop using your model
immediately and turn off both the model’s receiver and the transmitter. Replace the transmitter batteries im-
mediately with fresh AA batteries to prevent loss of control of your model.
b. Always check the voltage of the transmitter before use.
6. Always be sure to insert the batteries correctly according to the polarity markings, or the transmitter may be damaged.
7. When the transmitter will not be used for 1 week or more, remove the batteries to prevent damage from leaks and
corrosion.
Setting the ESC:
The ESC in your vehicle is pre-programmed to work best with the HRS3.2 radio system. Use with another radio system