background image

360137-D/D

13

i.Series® Models

7.6 

Mute and Disable Active Alarms

Audible alarms may be muted by touching the 

Mute

 button to set delay.

 

:15

Unmuted Muted

7.7 

Access Control (Optional)

Allows user-specific secure access to the freezer.

NOTE

► 

During a power failure, the backup battery provides power to the monitoring system 

and the power failure alarm.  If the backup battery is not functioning, the power failure 

alarm will not be activated.

► 

During a power failure, the backup battery continues to provide power to the optional 

Access Control lock (if equipped).  If the backup battery is not functioning, the 

optional Access Control lock will not secure the door.

► 

During a power failure, the optional Access Control lock will remain locked until 

battery power is depleted or until the backup battery key switch is switched OFF.

► 

Switching the backup battery key switch OFF will disable the monitoring system.

► 

During a power failure, switch the battery backup switch OFF and use the mechanical 

door key to provide secure storage for freezer contents.

7.7.1 Setup

  >  

  >  

  >  Access Setup

Configure and manage use-specific accounts to allow 

controlled access to the freezer.

► 

Enter the supervisor PIN to set up Access Control

► 

Initial factory supervisor PIN = 5625

NOTE 

The supervisor PIN can not be deleted, and should be changed to prevent unauthorized 

user ID setup.  The supervisor PIN does not allow access to the unit.  At least one user 

ID must be set up to gain access to the unit.

Summary of Contents for Horizon HLF105





























Reviews: