background image

360094-1/M

11

Operation

Start a Cycle:

Confirm the chamber has been filled to the appropriate level.

Confirm the water temperature stabilized at temperature setpoint.

Enable or disable agitation motion, depending on your organization’s specific needs.

Load overwrapped bags into basket(s), with security snap(s) as needed.

For each basket, press the 

CYCLE TIME

 button to select the desired time.

Press the 

CYCLE START

 button to lower basket and start the thaw cycle.

NOTE 

One DH4 and DH8 models, the cycle time, cycle start, and lift out for each basket 
is controlled individually.

8 .6 .2 

Stop, Pause, or Resume a Thaw Cycle

When a thaw cycle is stopped or paused, the basket lifts out of the chamber before the thaw cycle is 
completed.

► 

Press the 

LIFT OUT

 button to raise the basket and temporarily pause the thaw cycle.  The remaining 

time is displayed on the cycle time indicator.

► 

Press the 

LIFT OUT

 button again to resume the thaw cycle.  The basket is lowered into the chamber 

and the agitation motion resumes.

► 

The hold (“HO”) setting may be selected while the thaw cycle is paused (

LIFT OUT

 button pressed).

8 .6 .3 

Complete a Thaw Cycle

When a thaw cycle reaches the end of its programmed time setting, the basket stops agitating, lifts out, 
and opens.  An audible alert sounds to indicate the thaw cycle has completed, and the cycle time indicator 
resets to the previously selected time setting.

8 .7 

Unload Bags

CAUTION

► 

Do not manually lift the baskets out of the chamber.  Manually lifting baskets will 

damage the system.  Press the 

LIFT OUT

 button to raise the baskets.

► 

Press the 

LIFT OUT

 button only if the baskets are installed.  The basket must be 

installed for the lift out system to operate correctly.

Unload the bag(s):

On control panel, press the 

LIFT OUT

 button to raise and open basket.

LIFT OUT button.

Remove the security snap from the basket.

Unhook the slot at the top of the overwrap bag from the tab on the basket.

Remove the overwrap bag from the basket.

Remove the plasma bag from the overwrap bag.  Discard the overwrap bag.

Summary of Contents for OuickThaw DH2



















Reviews: