background image

360094-1/M

9

Operation

8 .5 

Load Bags

CAUTION

► 

Do not manually lift the baskets out of the chamber.  Manually lifting baskets will 

damage the system.  Press the 

LIFT OUT

 button to raise the baskets.

► 

Press the 

LIFT OUT

 button only if the baskets are installed.  The basket must be 

installed for the lift out system to operate correctly.

► 

DH2 basket holds 2 standard bags.

► 

DH4 uses 2 of the same basket used in the DH2, for a total capacity of 4 compartments.

► 

DH8 basket holds 8 standard bags.

NOTE 

On the DH8, the divider between compartments on each side can be removed to 
hold jumbo or wide bags.

When thawing a plasma bag (of any type or size), a plasma overwrap bag must be used.  The plasma 
bag is placed inside the overwrap bag, and the overwrap bag is attached to the basket.

Overwrap bags provide the following benefits:

► 

Secure the plasma bag to the basket

► 

Protect the plasma bag from water-borne contaminants

► 

If the plasma bag breaks, the contents will not contaminate the water bath

NOTE 

Use only 1 overwrap bag, of the appropriate size, per plasma bag.

The following recommendations will aid in thawing plasma bags:

► 

Use security snaps on smaller bags that tend to float

► 

Load plasma bags together that require the same thaw time

► 

When loading 2 bags on same side of the basket in DH8 models, place thicker bag in the front-most 
compartment

Load the bag(s):

Insert plasma bag into appropriate size overwrap bag.

On control panel, press the 

LIFT OUT

 button to raise and open basket.

LIFT OUT button.

3  DH8 models:

 Remove the basket divider if a jumbo or wide bag is loaded.

► 

Squeeze sides of the divider together and pull divider away from basket.

Removing divider from DH8 basket.

Summary of Contents for OuickThaw DH2



















Reviews: