background image

360094-1/M

4

General Information

General Recommendations

3 .1 

Intended Use

Helmer plasma thawing systems are intended for thawing frozen blood products and other medical, 

biological, and scientific products.

3 .2 

General Use

Allow plasma thawer to come to room temperature before switching power on.
During initial startup, low temperature alarm may sound while plasma thawer reaches operating temperature.

3 .3 

Initial Loading

Allow chamber temperature to stabilize at the setpoint before thawing frozen product.

Specifications

DH2

DH4

DH8

Physical
Height (Baskets Lowered)

16.25” (413 mm)

16.25” (413 mm)

16.25” (413 mm)

Height (Baskets Raised)

23.00” (584 mm)

23.00” (584 mm)

23.00” (584 mm)

Width

15.50” (368 mm)

21.75” (553 mm)

21.75” (553 mm)

Depth

15.50” (394 mm)

15.50” (394 mm)

22.50” (572 mm)

Weight

38 lbs (17 kg)

58 lbs (26 kg)

74 lbs (34 kg)

Chamber Volume

2.2 gal. (8.2 L)

4.75 gal. (18 L)

8.5 gal. (32 L)

Basket Capacity

2 units

4 units

8 units

External Port

Standard (for external thermometer)

Electrical
Input Voltage and Frequency

100 V, 50 Hz / 115 V, 50-60 Hz / 230 V, 50-60 Hz

Voltage Tolerance

±10%

Circuit Breakers

5 A (100 V)

4 A (115 V)

2 A (230 V, quantity 2)

10 A (100 V)

7 A (115 V)

4 A (230 V, quantity 2)

15 A (100 V)

15 A (115 V)

6 A (230 V, quantity 2)

Power Consumption 

(1)

3.0 A (100 V)

2.5 A (115 V)

1.25 A (230 V)

8.0 A (100 V)

6.0 A (115 V)

3.0 A (230 V)

12.0 A (100 V)

10.0 A (115 V)

5.0 A (230 V)

Power Source 

(2)

Varies (refer to product specification label)

Control and Monitoring
Interface

Integrated temperature control, monitoring, and display

Alarms

High temperature, low temperature, lift-out malfunction

Environmental

Application

► 

Indoor use only

► 

Altitude (maximum): 2000 m

► 

Ambient temperature range: 15 ºC to 32 ºC (59 ºF to 90 ºF)

► 

Relative humidity (maximum for ambient temperature): 80% for 

temperatures up to 31 ºC (88 ºF), decreasing linearly to 50% at 

40 ºC (104 ºF)

(1) 

Power consumption is measured in full-load Amperes.

(2) 

Product specification label is located on the left side of the plasma thawer.

Summary of Contents for OuickThaw DH2



















Reviews: