background image

TECHNICAL SPECIFICATIONS:

 

 

Front frame dimensions: 89х89х9mm 

 

Back dimensions: 53х53х28mm  

 

Material: Flame retardant plastic, tempered glass 

 

Colour: silver frame, black or white glass 

 

LCD: 73x42mm, black with white icons 

 

4 sensitive capacitive touch buttons 

 

Operating temperature

: -10°С – +40°С 

 

Power supply: 100V – 230VAC, 50Hz/60Hz 

 

Power consumption: 1.5W 

 

Maximum resistive load: 16А  3600W 

 

Relay life time: 100.000 switches 

 

Internal temperature sensor 

o

 

Measurement range:  -40°C to +125°C 

o

 

Accuracy

: ±0.5°C

 

 

 

Internal humidity sensor 

o

 

Measurement range: 0 – 80%RH 

o

 

Accuracy

: ±3.0%RH  

 

External floor temperature sensor 

o

 

NTC 10kOhm 

o

 

Measurement range:  -30°C to +80°C 

o

 

Accuracy

: ±0.5°C

 

 

 

Energy consumption meter 

 

IP class: IP21 

 

Z-Wave frequency: EU-868/869 MHz  
(other frequencies available on request) 

 

Z-Wave SDK: V6.51.06

 

 

Z-Wave Plus module: ZM5202 

 

FUNCTIONAL SPECIFICATIONS (FEATURES): 

 

Inclusion/exclusion into/from z-wave network 

 

Association control of 10 devices from network 

 

4 operation modes: ECO, GEN, DRY, MANUAL 

 

Choosing a temperature sensor for operation 

 

Floor temperature only 

 

Air temperature only 

 

Floor + Air temperature 

 

Power regulator (Automatic ON/OFF timer) 
Time cycle: 10-90 minutes 

 

Usable with different NTC-sensor  

 

Temperature sensors calibration 

 

Temperature set intervals: 4°C to 37°C 

 

Temperature limiter 

 

Choosing a temperature hysteresis 

 

Choosing a degree  (Celsius / Fahrenheit) 

 

Adjustable LCD brightness 

 

LCD standby mode 

 

Child lock 

 

Consumption meter reset 

 

Factory reset 

 

OTA function (Firmware update over the air). 

Z-WAVE CLASSES: 

CLASSES GENERIC_TYPE_THERMOSTAT  
SPECIFIC_TYPE_THERMOSTAT_GENERAL_V2 
COMMAND_CLASS_BASIC  
COMMAND_CLASS_THERMOSTAT_SETPOINT_V3 
COMMAND_CLASS_THERMOSTAT_SETBACK 
COMMAND_CLASS_THERMOSTAT_MODE_V3 
COMMAND_CLASS_THERMOSTAT_OPERATING_STATE 
COMMAND_CLASS_SENSOR_MULTILEVEL_V7 
COMMAND_CLASS_VERSION  
COMMAND_CLASS_MANUFACTURER_SPECIFIC 
COMMAND_CLASS_ZWAVEPLUS_INFO 
COMMAND_CLASS_METER_V3 
COMMAND_CLASS_DEVICE_RESET_LOCALLY 
COMMAND_CLASS_POWERLEVEL 
COMMAND_CLASS_CONFIGURATION_V2 
COMMAND_CLASS_ASSOCIATION  
COMMAND_CLASS_ASSOCIATION_GRP_INFO 
COMMAND_CLASS_FIRMWARE_UPDATE_MD_V3

 

 

Summary of Contents for HE-ZW-THERM-FL1
















Reviews: