background image

Helvar iDim Remote Control (304) User Manual

Special Functions using iDim Remote

Note: All standard operation settings such as scene recall, modify and store scene are still possible when the iDim Remote is in 

special 

function mode.

Advanced Configuration with iDim Studio Software

4

O

5

6

7

1

2

3

+

Fn

Ch

10 s

125

ms

IDim Sense LED flash feedback

Enable IR Receiver

  

To enable the Infra-red receiver of a controller:

1.

Ensure the iDim Remote is in special function mode.

2.

Point the remote at a controller.

3.

Press and hold DALI 1 modifier up and Fn key at the same time 
for 10 seconds.

4

O

5

6

7

1

2

3

+

Fn

Ch

10 s

125

ms

IDim Sense LED flash feedback

Disable IR Receiver

 

To disable the Infra-red receiver of a controller:

1.

Ensure the iDim Remote is in special function mode.

2.

Point the remote at a controller.

3.

Press and hold DALI 1 modifier down and Fn key at the same 
time for 10 seconds.

4

O

5

6

7

1

2

3

+

Fn

Ch

10 s

125

ms

IDim Sense LED flash feedback

Lock iDim Sense Mode Selector Ring

  

To lock the mode selector ring of an iDim Sense:

1.

Ensure the iDim Remote is in special function mode.

2.

Point the remote at the iDim Sense you wish to lock.

3.

Press and hold DALI 2 modifier up and Fn key at the same time 
for 10 seconds.

Note:

When locked, the iDim Sense mode selector ring
can still be manually turned. However, the modes will
be ignored unless the mode selector ring is unlocked.

4

O

5

6

7

1

2

3

+

Fn

Ch

10 s

125

ms

IDim Sense LED flash feedback

Unlock iDim Sense Mode Selector Ring

  

To unlock the mode selector ring of an iDim Sense:

1.

Ensure the iDim Remote is in special function mode.

2.

Point the remote at the iDim Sense you wish to unlock.

3.

Press and hold DALI 2 modifier down and Fn key at the same 
time for 10 seconds.

Note:

iDim Sense will remain in the selected mode (and in user defined 
mode where applicable) until the mode selector ring
is turned again.

Transfer settings to iDim Sense using iDim

Remote 

To transfer settings to iDim Sense using iDim Remote:
1.

Point the remote at a controller.

2.

Press OK and Fn key at same time.

625 ms

125

ms

125

ms

125

ms

125

ms

iDim

Summary of Contents for iDim 304











Reviews: