background image

Data  subject  to  change  without  notice.  For  more  information  visit  our  website:  www.helvar.com

9

Notes:

•  “Manual  ON, Automatic  OFF”  feature  =  PIR  will  not  switch  the  lights  on  when  movement  is

detected, but will switch them off if no movement is detected.

• Regardless of other light level commands (e.g. changes in the constant light level), an enabled

PIR will switch the lights to the PIR OFF scene  if no movement is detected within its programmed

delay time.

Presence detector (PIR)

• Simultaneously press & hold “

3

” & “

4

” for 10 seconds.

• The operation is confirmed by flashing the lamps.

Note:

This also resets all scenes.

10 seconds

1

3

4

2

0/1

Disable “Manual ON, Automatic OFF” feature

(only possible through initial configuration / minisensor reset)

1

3

4

2

0/1

10 seconds

10 seconds

1

3

4

2

0/1

• Simultaneously press & hold “

0/1

” & “

2

” for 10 seconds.

• Simultaneously press & hold “

0/1

” & “

3

” for 10 seconds.

Note:

This must be done before setting the PIR delay time. If

you require a different delay time please see PIR delay

time settings instructions

.

Enable “Manual ON, Automatic OFF” feature with 20seconds delay time

1

3

4

2

0/1

10 seconds

1

3

4

2

0/1

10 seconds

• Simultaneously press & hold “

0/1

” & “

2

” for 10 seconds.

• Simultaneously press & hold “

0/1

” & “

4

” for 10 seconds.

Note:

This must be done before setting the PIR delay time. If

you require a different delay time please see PIR delay

time settings instructions.

Enable “Manual ON, Automatic OFF” feature with 20min. delay time

1

3

4

2

0/1

10 seconds

• Simultaneously press & hold “

0/1

” & “

2

” for 10 seconds.

• The operation is confirmed by flashing the lamps.

Disable PIR.

10 seconds

1

3

4

2

0/1

• Simultaneously press & hold “

3

” & “

4

” for 10 seconds.

• The operation is confirmed by flashing the lamps.

Note:

This also resets all scenes.

Enable PIR 

(only possible through initial configuration / minisensor reset).

Summary of Contents for Minisensor

















Reviews: