background image

14

Chapter 2: Installation

Power/Data Cable Considerations

Before mounting the V102 consider the following regarding power/data 
cable routing:

Cable must reach an appropriate power source

Cable may connect to a data storage device, computer, or other 
device that accepts GPS data

Avoid running the cable in areas of excessive heat

Keep cable away from corrosive chemicals

Do not run the cable through door or window jams

Keep cable away from rotating machinery

Do not crimp or excessively bend the cable

Avoid placing tension on the cable

Remove unwanted slack from the cable at the V102 end

Secure along the cable route using plastic wraps

Improperly installed cable near machinery can be dangerous

Flush Mount

The bottom of the V102 contains four holes for flush mounting the unit to a 
flat surface (Figure 2-7). The flat surface may be something you fabricate per 
your installation, an off-the-shelf item (such as a radar mounting plate), or an 
existing surface on your vessel.

Note:

 Hemisphere GPS does not supply the mounting surface hardware. 

You must supply the appropriate fastening hardware required to complete 
the installation of the V102.

Summary of Contents for V102 G





























































Reviews: