hengel Bi-Tronic Control User Instructions Download

Page: 10 / 13

Hengel Industrie

ZA, Les Berges du Rhins - 42120 PARIGNY - FRANCE
Tél : +33 (0)4 77 23 40 00 - Fax : +33 (0)4 77 23 40 09

Email: infos@hengel.com
Website: www.hengel.com

Notice-EN-BITRONIC-ST-F-1

4.0

25.0

3.5

27.2

3.3.1 CHANGE SET POINTS

Press the “

Plus

” or “

Minus

” key.

The

blocking temperature LED blinks in orange

and

the display shows a temperature.

Adjust the temperature using the “

Plus

” and “

Minus

”

buttons, then “

Validate

”.

Then, the

proving temperature LED blinks in orange

Adjust the temperature using the “

Plus

” and “

Minus

”

buttons, then “

Validate

”.

Then, the

hygrometry LED blinks in orange

. Adjust

the rate using the “

Plus

” and “

Minus

” buttons, then

“

Validate

”.

Then, the

proving time LED blinks in orange

. Adjust

the time using the “

Plus

” and “

Minus

” buttons, then

“

Validate

”.

70.0

4:30

75.0

5:00

Summary of Contents for Bi-Tronic Control














Search results

Summary of Contents for Bi-Tronic Control

Reviews:

Related manuals for Bi-Tronic Control

Brands by name

Popular brands

hengel Bi-Tronic Control, User Instructions

Search results

Summary of Contents for Bi-Tronic Control

Reviews:

Related manuals for Bi-Tronic Control

Brands by name

Popular brands