background image

 
 
 

 
 
 

II 

User manual Compact Eco-range 

 
 
 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

2007 HFE vacuum systems b.v. 

 
All rights reserved. 
No part of this document may be reproduced and/or published by means of printing, photocopy, microfilm or any other method, without 
the prior written permission of the manufacturer. This also applies for the accompanying illustrations and/or diagrams and schematics. 
 
The information in this document is based on the general data associated with the construction, material qualities and working methods, 
known at the moment of publication, so that we reserve the right to make changes without giving prior notice. 
 
This document is applicable to the indicated models of the Henkovac packing machine in the version supplied. The manufacturer 
therefore does accept any liability for any form of damage or injury resulting from deviating from the specifications of these machines as 
supplied to you. 
All possible care was taken when creating this document, but the manufacturer accepts no liability for mistakes or any consequences 
thereof. 

 
TAKE THE TIME TO READ THIS DOCUMENT THOROUGHLY TO ACQUAINT YOU WITH THE CORRECT 
AND APPROPRIATE USE OF THE HENKOVAC VACUUM PACKING MACHINES. 

2007-05

 

Summary of Contents for COMPACT ECO Series
















Reviews: