6 •
Important: Always read and follow instructions.
Initial Screen
Dimensions gauge: pulling it out, it measures
the wheel dimensions (
selects the correction type
displays the residual out-of-balance
(option)
wheel locks/unlocks
main functions screen
(
MENU ACCESS DIAGRAM)
WHEEL DIMENSIONS
SETTING).
If the machine remains on the initial screen for a cer-
tain amount of time without being used, the system
is automatically switched to a screen-save. Striking
of any key, movement of the wheel or di
diameter gauge will cause automatic switching from
the screen-save menu to the initial screen.
CAUTION
When the screensaver is active, automatic
starting activated by the wheel guard is
not available for safety reasons.
Standard Balancing (Clip-On Counter-
weights)
Wheel dimensions setting
Using the special grip, move the end of gauge
against the rim as shown in the figure:
Hold the gauge in position for at least 2 seconds.
If the acoustic signal is enabled ( MENU - ACOUSTIC
SIGNAL), the dimensions acquisition is accompanied
by a beep.
Set the gauge to the rest position.
Set the width value shown on the tire and proceed
with balancing the wheel.
If the wheel dimensions have been entered incor-
rectly, the parameters can be modified without repeat-
ing the balancing spin.
From the measurement screen press
ENGLISH
...
Indicators, selection made
Push button, FUNCTIONS MENU
Push button, menu selection confirmation
Push button, cycle start
Push button, cycle stop
->
ENGLISH
...
Indicators, selection made
Push button, FUNCTIONS MENU
Push button, menu selection confirmation
Push button, cycle start
Push button, cycle stop
.
Manual width setting
Press
ENGLISH
...
Indicators, selection made
Push button, FUNCTIONS MENU
Push button, menu selection confirmation
Push button, cycle start
Push button, cycle stop
/
ENGLISH
...
Indicators, selection made
Push button, FUNCTIONS MENU
Push button, menu selection confirmation
Push button, cycle start
Push button, cycle stop
to set the width “b” in
manual mode.
Normally the “nominal” width is indicated on the
wheel; otherwise, measure the dimension “b” with
the supplied caliper gauge.
selects the correction type
displays the residual out-of-balance
(option)
wheel locks/unlocks
main functions screen
(
MENU ACCESS DIAGRAM)
selects the correction type
displays the residual out-of-balance
(option)
wheel locks/unlocks
main functions screen
(
MENU ACCESS DIAGRAM)
selects the correction type
displays the residual out-of-balance
(option)
wheel locks/unlocks
main functions screen
(
MENU ACCESS DIAGRAM)
selects the correction type
displays the residual out-of-balance
(option)
wheel locks/unlocks
main functions screen
(
MENU ACCESS DIAGRAM)
13
b
b
ENGLISH
Use and maintenance manual
selects
user control
/
/
selects the type of
weight to be applied
selects the manual
dimension presetting
screen
returns to the initial
screen
In the standard machine setting as VIRTUAL SONAR (AWA and AUTOADAPTIVE enabled), at the end of the automatic
distance and diameter measurement, perform a measuring spin.
In the case of particular rims, the wheel balancer may ask you to set the tyre width value in mm.
Set the width value shown on the tyre and proceed with balancing the wheel.
If the wheel dimensions have been entered incorrectly, the parameters can be modified without repeating the
balancing spin.
From the measurement screen press
->
.
6.2.1.1 M
Press
/
to set the width “b” in manual mode.
Normally the “nominal” width is indicated on the wheel; otherwise, measure the dimension “b” with the supplied
caliper gauge.
Use of the wheel balancer
Summary of Contents for Coats 1185
Page 29: ...Important Always read and follow instructions 23 Notes...
Page 30: ...24 Important Always read and follow instructions Notes...
Page 31: ...Important Always read and follow instructions 25 Notes...
Page 32: ...85611754 00 08 20 Copyright 2020 Hennessy Industries LLC All Rights Reserved Printed in USA...
