HENNESSY INDUSTRIES Coats 4050A Safety Instructions, Operating Instructions, Installation Instructions, Maintenance Instructions Download

Page: 1 / 16

1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359

Manual Part No.: 8111144 00

HENNESSY INDUSTRIES INC. Manufacturer of AMMCO

, COATS

and BADA

Automotive Service Equipment and Tools.

Revision:

02/97

Safety Instructions

Operating Instructions

Installation Instructions

Maintenance Instructions

READ these instructions before placing unit in
service KEEP these and other materials delivered
with the unit in a binder near the machine for
ease of reference by supervisors and operators.

4050A

Tire Changer

For servicing single piece automotive and
most light truck tire/wheel assemblies

Summary of Contents for Coats 4050A

















Search results

Summary of Contents for Coats 4050A

Reviews:

Related manuals for Coats 4050A

Brands by name

Popular brands

HENNESSY INDUSTRIES Coats 4050A, Safety Instructions, Operating Instructions, Installation Instructions, Maintenance Instructions

Search results

Summary of Contents for Coats 4050A

Reviews:

Related manuals for Coats 4050A

Brands by name

Popular brands