HENNESSY INDUSTRIES Coats Rim Clamp RC-50M Installation Instructions, Operating Instructions, Safety Instructions, Maintenance Instructions Wit Download

Page: 1 / 16

1601 J. P. Hennessy Drive, LaVergne, TN USA 37086-3565 615/641-7533 800/688-6359

Manual Part No.:

85000625 00

HENNESSY INDUSTRIES INC. Manufacturer of AMMCO

, COATS

and BADA

Automotive Service Equipment and Tools.

Revision:

06/07

READ these instructions before placing unit in
service KEEP these and other materials delivered
with the unit in a binder near the machine for
ease of reference by supervisors and operators.

RC-50M

Rim Clamp

Tire Changer

For servicing motorcycle and ATV tire/wheel assemblies

See

Operating

Instructions

on page 2.

Installation Instructions

Operating Instructions

Safety Instructions

Maintenance Instructions

with Parts List

Summary of Contents for Coats Rim Clamp RC-50M

















Search results

Summary of Contents for Coats Rim Clamp RC-50M

Reviews:

Related manuals for Coats Rim Clamp RC-50M

Brands by name

Popular brands

HENNESSY INDUSTRIES Coats Rim Clamp RC-50M, Installation Instructions, Operating Instructions, Safety Instructions, Maintenance Instructions Wit

Search results

Summary of Contents for Coats Rim Clamp RC-50M

Reviews:

Related manuals for Coats Rim Clamp RC-50M

Brands by name

Popular brands