background image

iv •

Important: Always read and follow the operating instructions.

Vertical Slide Locking Handle —

Locks and unlocks vertical slide

and sets correct vertical position to maintain head/wheel clearance.

Swing Arm Adjustment Knob —

Adjusts swing arm/vertical slide

assembly for proper horizontal positioning of duckhead

®

.

Tower —

Support for horizontal swing arm and vertical slide.

Table Top Rotating Handle Receiver —

Insert table top rotating

handle into this receiver (4 receivers / 90 degrees apart).

Clamping Screw —

Use to open or close rim clamps.

Table Top Locking Knob —

Locks and unlocks the table top posi-

tion. Use to prevent the table top from rotating.

Table Top Rotating Handle —

Use for extra leverage when rotat-

ing table top during tire removal.

Table Top  —

Rotating platform for tire changing.

Three Position Motorcycle Clamps —

Holds wheel to table top

for tire changing (4 clamps / 90 degrees apart).

Motorcycle DuckHead

®

Mounts and demounts tire from wheel.

Bead Loosener (Optional) —

Use to loosen bead of tires.

Mounting Tabs  —

Use to adjust bead loosener position to match

tire/rim combination.

Mounting Slots —

Attaches bead loosener to tire changer.

Principal Operating

Parts

Know Your  Unit

Compare this illustration with the unit before placing

it into service. Maximum performance and safety will
be obtained only when all persons using the unit are
fully trained in its parts and operation. Each user should
learn the function and location, of all controls.

Prevent accidents and injuries by ensuring the unit is

properly installed, operated and maintained.

Summary of Contents for Coats Rim Clamp RC-50M

















Reviews: