Clock, RPM, Wheel, Divider, Unit, Maintenance , Thermometer, fuel meter and ODO
15. It displays " 1 XXX" and the selected unit. Follow the item 2 of button
operation to finish the temperature warning setting and go to
thermometer 2 setting.
16. Thermometer 2 setting It displays " 2 °C , °F or oFF", each press of
RESET button converts °C , °F or Off, the temperature bars will
disappear when you select oFF mode; press MODE button to confirm
temperature setting and jump to temperature warning setting.
17. It displays " 2 XXX" and the selected unit. Follow the item 2 of button
operation to finish the temperature warning setting and go to fuel
sensor resistance setting.
18. It displays “on, off or rES” and , the setting range of “on” from 10r to
990r, press and hold RESET button can change digits quickly, follow the
item 2 to select a resistance same as your fuel sender and jump to
sensor type of **LAP timer setting. The fuel meter bar will disappear if
you select oFF mode. In “rES” mode connecting the input wire to 0v can
bring on the fuel symbol and/or LED indicator instantly.
19. **It displays Ir, EF1, EF2 or EF3, Ir means you elect IR receiver as the
sensor of LAP timer, and the selection of EF1, 2 or 3 is a magnetic field
sensor for LAP timer, the number of 1, 2 or 3 is means the number of
magnetic sensor in track, for example EF2 means the track has 2
magnetic sensor and it will combine 2 sensing signals in one. Follow the
item 2 to set sensor type of LAP timer and jump to odometer setting.
20. It displays “ODO & 00000X km”, the “X” is from odometer testing in
factory, follow item 2 to setting a desired odometer and jump to clock
setting or return to Normal Mode. This setting screen will disappear
when the odometer is over 30km (18.6Miles) or your setting is over
30km.
Press 2 Seconds.
Mode Button, RESET Button, MODE Reset, Mode + Reset 2 seconds.
1. Setup operations include 12/24hour clock, bar rpm scale, shift warning
RPM, numbers of engine signal, wheel circumference, signal divider,
units, decimal, maintain reminder, *voltage warning, *units of
temperature, *temperature warning, fuel meter input resistance
selection, sensor type of **LAP timer and odometer adjustment.
These must be set up step by step. The computer will be automatically
revert to normal mode if no button is pressed for 75 seconds at any
setting screen.
2. Press both MODE & RESET buttons to go into setting mode. In setting
mode, each press of the RESET button increments the flashing digit by
1 or converts units. Press MODE button to confirm the digit setting and
jump to next digit or next setting screen to be set. Press MODE button
for 2 seconds at any setting screen to finish the setting and go to
normal mode.
3. It displays "12 or 24H, and XX:XX-XX" symbols as well AM/PM in
case you select 12H. Operates buttons as descriptions of item 2 to
finish clock setting and jump to 10,000/20,000rpm scale setting.
4. It displays 10,000rpm scale, press RESET button to convert 10,000 or
20,000rpm. Press MODE button to confirm the setting and jump to
shift RPM warning setting.
5. It displays the default "RPM r06500", the digit “0” flash. Follow the
item 2 of button operation to finish the shift RPM warning setting and
jump to engine specification setting.
6. It displays "RPM SP 1r1P", the default value is 1r1P; there are 6
options: 1r1P, 2r1P, 3r1P, 1r2P, 1r3P, 1r4P. “r” means the numbers of
engine rotation, “P” means number of signals from engine. For
example the value 2r1P means the engine rotate 2 turns to output one
signal.
7. Press RESET button to move in loop sequence from one to another
value of the 6 values. Press MODE button to confirm the setting and go
to wheel circumference setting screen.
8. In "SPD cXXXX" display, "c" means "Circumference in mm", following 4
default digits; flashing digit is digit to be set. Follow the item 2 of
button operation to finish the wheel circumference setting and jump
to signal divider setting to set the number of pulses from the speed
sensor per turn of the wheel.
9. It displays "SPD P-001" for signals to be divided. Follow item 2 of
button operation to finish the setting and jump to unit setting.
10. It displays KM/H or MPH, each press of RESET button converts unit;
press MODE button to confirm unit setting and jump to speedometer
decimal point setting.
11. It displays “SPD 99.9Km/H” on or “SPD 99Km/H off”, the decimal
point will not be displayed when “off” is selected. Follow the item 2
of button operation to finish the decimal setting and jump to
maintain reminder setting.
12. It displays and RT, TRIP or OFF. RT has default of 100 hours, TRIP
has 1000km (621Miles) default. Follow the item 2 of button
operation to finish the maintain reminder setting and jump to
voltage warning setting. The maintain reminder function will be
disappear when select “OFF”.
13. It displays “ b-on and a flashing numbers of voltage” to be set,
“b-on” means battery warning on voltage – when the voltage falls
below this the LED will come on, setting range from 11.0 to 14.9V. It
displays “ b-off and a flashing numbers of voltage”, “b-off” means
battery warning off voltage, setting range from 11.0 to 14.9V to, but
b-off voltage must larger than b-on voltage – when this voltage is
exceeded the LED will go off. Follow the item 2 of button operation
to finish the voltage warning setting and jump to temperature unit
setting.
14. Thermometer 1 setting It displays " 1 °C , °F or oFF", each press of
RESET button converts °C , °F or Off, the temperature bars will
disappear when you select oFF mode; press MODE button to confirm
temperature setting and jump to temperature warning setting.
**LAP review operations:
1. In the LAP mode, press MODE button to review the 1st storage data, it
displays number of lap and lap timer.
2. Press the LAP button to switch between lap timer or average speed of
the same LAP; each press of the MODE button displays data for the next
lap.
3. Press and hold LAP buttons for 2 seconds to go out LAP mode and return
to normal mode.
Normal Mode
Lap Mode
Lap Review Mode
Lap
2 Sec.
Lap
2 Sec.
Mode
Mode
Mode
Lap
Mode
WHEEL CIRCUMFERENCE TABLE
Tire Size
Circumferen
ce number
(mm)
Tire Size
Circumferen
ce number
(mm)
Tire Size
Circumferen
ce number
(mm)
23 inch
24 inch
25 inch
26 inch
19 inch
20 inch
21 inch
22 inch
15 inch
16 inch
17 inch
18 inch
1835
1915
1995
2075
1516
1596
1676
1756
1197
1277
1357
1436
1. The details below have been calculated using following formula: Tire
Diameter (inches) x 25.4(mm/inches) x 3.1416 = wheel circumference
(in mm).
2. Identify the tire size (not wheel size) of your ATV/Motorcycle when you
need to change different tire size and key in the corresponding number
shown in the following chart.
3. These values are approximate and will differ for different brands of tire,
we would always recommend that you measure the distance travelled
per revolution of the wheel in mm and enter this into the computer.
4. The computer calculates the wheel rotating length between 2 passes of
the magnet; use this table to find the settings when you are using a reed
sensor or an universal hall sensor with magnet to measure your speed.
5. If you are using a cable drive speed sensor then enter the number of
turns of the speedo cable per turn of the wheel into the “p” screen.
6. You can use more magnets, but the number of magnets must be entered
into the “p” screen.
7. The computer has a built-in software divider (“p” screen) setting from
1 to 199 for different speed signal application, refer to the divider
setup, one means one wheel revolution creates one signal. You have
to input the number of signal per wheel revolution to have a correct
speed.
