background image

General hazard warnings

16

3  General hazard warnings

3.1 Dangers

Warning!
Maintenance and repair work can 

cause hand injuries.
Observe all of the safety precautions.

Observe the safety systems and safety precautions that are 

described in this manual. The pump is operated by the control 

elements or by the superordinate system. Keep the access 

area free from any clutter while operating the pump in order 

to ensure unrestricted access at all times.

3.2 

Danger zones on the pump

A radius of approximately 1 m around the pump is designated 

a danger zone for maintenance and cleaning work. The 

control elements form the only operating area.

Caution!
Material escaping from the pump can 

cause injuries.
Install or secure the pump in such 

a way that the direction of pumping 

is away from areas personnel may 

frequent.

3.3 

Assembly, operation and maintenance personnel

Assembly, operation and maintenance personnel are re-

sponsible for the transportation, fitting, installation, operation, 

cleaning and reparation of the pump.

1.  Only trained and authorised persons may 

install and operate the pump.

2.  Clearly define and observe the respon-

sibilities for operating the pump.

3.  Observe the shut off procedures speci-

fied in the operating manual for all work 

processes (operation, maintenance, 

repair, etc.).

4.  The operator must not impair the safety 

of the pump.

5.  The operator must ensure that only au-

thorised persons work with the pump.

6.  The user must notify the operator im-

mediately of any alterations to the pump 

which affect the safety measures.

7.  The operator may only actuate the pump 

if it is in a perfect condition.

8.  The operator must provide the operat-

ing staff with the appropriate protective 

equipment according to the statutory 

requirements and the pumped medium.

3.4 

Installation of replacement parts and wear parts

Replacement parts and accessories that are not supplied 

by the manufacturer are unchecked and, as such, are not 

approved. The installation and/or use of such products may 

adversely affect the specified properties of your pump.
The manufacturer accepts no responsibility whatsoever for 

any damage caused by the use of non-original parts and 

accessories.

Summary of Contents for herborner.X























































Reviews: