background image

TW-820T 

3.Safety Precautions (Be Sure to Read This)

 

This section describes the matters to be observed in order to prevent harm to the users and other persons and 
damages to the property. 
■The following marks and displays classify and describe the extent of harm and damage caused by failing to observe 
the display content and using this product wrongly. 

 

This display column shows "a failure to do observe it could result in only the personal 
injury or property damage"

■Handling this product 

 

This product is the wireless communication equipment made of precision parts. Do not 
disassemble or modify it. Or the accident or fault may occur. 

 

■Use and storage environment 

 

DO NOT USE OR STORE the product in the following places to prevent defects, malfunction, 
deterioration, fire, and electric shock: 

 

Do not use and store it in places exposed to direct sunlight, 

 

Do  not  use  and  store  it  in  places  where  liquids,  foreign  substances,  corrosive  gases  or 
combustible gases can enter the product, 

 

Do not use and store it in places with high humidity or where there is abundant oil smoke, 
dust, sand, etc. , 

 

Do not use it in an unstable place such as a wobbling table or an inclined plane, 

 

Do not use it in a place with vibration.

 

 

 

■Specific handling of this product 

 

This product is a radio equipment with certification of construction design. 

 

It is prohibited by law to disassemble or modify certified devices. 

 

 

Do not remove the certification label affixed to the case. It is prohibited to use any product   
without the label. 

 

 

This product is only available in the countries where the certification is acquired. 

 

 

 

This display column shows "a failure to do observe it could result in death or 
serious personal injury".

 

■Handling this product 

 

Do not use this product for application that requires the extremely high reliability affecting the 
human life. 

 

 

Do not use this product in the area which the radio wave reaches or not. 

 

■If a problem occurs during use 

 

When smoke comes or there is a strange smell, immediately stop usage and remove the power 
plug  from  the  outlet  because  it  may  cause  fire  and  electric  shock.  Request  the  dealer  or  our 
company to repair it. 

 

 

Caution

 

 

Warning

 

Summary of Contents for TW-820T

























Reviews: