background image

With your new wood stove you should find the following: 

Betjenings- og 

opstillingsvejlednin

g

dansk design  .  dansk

 kvalitet  .  dansk pro

duktion

www.heta.dk

dk

scan-line 80 og 80 Xl

Operating /
Instruction manual

Heta glove

Q.C. check 

Data plate

Heta A/S

Jupitervej 22 . DK-7620 Lemvig . Denmark

EN 13240:2001/A2:2004 - AEA - NS 3058/3059, Aus §15A

Testrapport: 300-ELAB-2276-EN

SN No. 

07-2017

Scan-Line 1000

Brændsel 

Træ

Ovnen er godkendt til intermitterende brug
Følg fabrikantens brugervejledning
Ovnen kan anvendes på røggassamleledning

Afstand til brændbart - bag ovn 

120 mm

Afstand til brændbart - foran af ovn 

1300 mm

Afstand til brændbart - side af ovn 

425 mm

Afstand til brændbart - under ovn 

---- mm 

Nominel ydelse / rum opvarmningsudelse 

7,7 kW

Middel CO emission i mg/Nm

3

  

960 mg/Nm

3

 

Middel CO emission 

0,077% 

Røggas temperatur  

204

C

Støv 

10 mg/Nm

3

Virkningsgrad 

86%

NOx 

80 mg/Nm

3

OGC 

76 mgC/Nm

3

DOP-Scan-Line 1000 2017

8057 0000-DK

Congratulations on your new stove. We are sure that you will be happy with your investment, espe-
cially if you follow the advice and instructions we have put together in these operating instructions.

Scan-Line 800 combustion chamber, and are therefore approved, like the Scan-Line 800, under EN 
13240, DINplus, 15 a B-VG and NS 3058/3059. Approval means that consumers can be sure, that 
the stove meets a range of specifications and requirements intended to ensure that the materials 
used are of good quality, that the stove does not adversely affect the environment, and hat it is 
economical to use.

Heta A/S

Jupitervej 22, 
DK-7620 Lemvig
Phone: +45 9663 0600
E-mail: heta@heta.dk

Copyright © 2014 
Heta is a registered 
trademark of Heta A/S

05.02.2021
0037-1415 Version 1,2

Printed in Denmark
Subject to printing errors 
and changes.

required tools are not supplied.

Summary of Contents for SCAN-LINE 80





















Reviews: