background image

 

Hettich AG, Seestrasse 204a, 8806 Baech, Switzerland 

Operator Manual_DancerPlus_EN_rev, 1.1 

 

 

 

Page 21 

2.3.8

 

Mains inlet device socket and mains switch

 

Please check the mains connection values on the label (rating plate) (see Fig. 11 no.3) on the rear 
side of the DancerPlus (see Fig. 6 no. 5) with regard to the power outlet to be used and observe 
the  country-specific  regulations  (e.g.  in  Germany,  DIN  VDE  0100,  power  outlet  with  residual 
current device). In case of doubt, please contact your technical service department, an electrician 
or electricity plant  
 
The mains inlet device socket (Fig. 6 no. 7) is located on the rear side of the DancerPlus, and the 
supplied power supply cable is connected here. Actuate mains switch on (Fig. 6 no. 8) so that 

the  “O”  position  protrudes  and  the  DancerPlus  is  switched  on.  Switch  on  the  other  system 

devices such as the vacuum pump and, if required, the cold trap. 
 

2.3.9

 

Lid connection cable 

Ensure that the lid connection cable (Fig. 6 no. 2) is not damaged and cannot be damaged, e.g. 
transportation damage, torn-out plastic cable gland, cable clamped between the basic device 
and the lid. 
Attention: this is not a standard cable and thus may only be replaced with an equivalent cable 
 

2.4

 

Conduct in the event of faults and irregularities 

The device may only be operated in flawless condition. If, as a user, you notice any irregularities, 
faults or damage, shut down the device immediately and inform your supervisor. 

 

2.5

 

Emergency switch-off of the DancerPlus 

Change the position of the power switch on the rear side of the device (Fig. 6 no. 8) and disconnect the power 
cable from the mains. 
 

If  the  DancerPlus  is  switched  off  or  disconnected  from  the  mains,  e.g.  following  a  power 
interruption, the release valve (release inlet) (Fig. 6 no. 3 and Fig. 5 no. 4) will automatically open, 
and if the vacuum pump is stopped or switched off, the lid may be opened after approx. 3 minutes 
in order to remove the samples from the DancerPlus.  
 
Depending  on  the  type  of  operation,  the  vacuum  chamber  surfaces  (Fig.  7),  the  temperature 
sensor, the rack and the sample vials / tubes contained within may still be hot after switching off 
or a power interruption. They may cause burns if touched. Use temperature-resistant protective 
gloves or allow the DancerPlus to initially cool down after switching off.  
Open the lid to allow it to cool down quicker. 
 
When dealing with samples, take account any potential biohazards and wear protective gloves 
and goggles. 
 

 

 

Summary of Contents for DancerPlus































Reviews: