13
5.
Parameter settings
5.1 Control parameters
This option makes it possible to change the value of parameters available in the selected installation scheme. In order to change parameters:
Press the following key combination: starting point - MAIN SCREEN: entry into the
MENU
, get to the option named
Parameters settings
, enter the
Parameter settings
menu
, get to the
Control parameters
option
, choose appropriate parameters
or
, edit
, change values
or
, accept values
(a continuous sound
signal), return to the main screen
.
ATTENTION ! Description of all the available parameters can be found in Table 3 – pages16-17
The display shows current option level and the controller values with the use of the ▼and ▲ cursors. The down cursor ▼ shows that there are parameters available
below the currently displayed options, whereas the up cursor ▲, indicates that there are parameters available above the currently displayed ones. The combination of
buttons for selected scheme no 3 is presented below.
5.2 Time program C
This option allows for setting a time program in which a device denoted by C (circulation pump, pool pump) in a given installation scheme will be working. In order to set or change the
C time program of devices:
Press the following key combination: starting point - MAIN SCREEN: enter the
MENU
with
(enter password), get to the option named
Parameters settings
with
, enter the
Parameter settings
menu with
, get to the option named
Time program C
with
, enter the option named
Time program C
with
, select time with
or
, accept
operation time (white square) or cancel operation time with
, accept and return (a continuous sound) with
, return to the main screen with
.
ATTENTION ! Time intervals are divided into 24h operation periods, settings for each hour are selected separately by marking it with a white square. The number of
squares marks the number of operation hours. Week days have been divided into three groups: Monday - Friday (Mo-Fr), Saturday (Sat), Sunday (Sun).
5.3 Circulation parameters
This option allows for setting all parameters connected with the operation of the tap water circulation pump. To change parameters of the C pump:
Press the following key combination: starting point – MAIN SCREEN: enter the
MENU
with
(enter password), get to the option named
Parameters settings
with
, enter the
Parameters settings
menu
, get to the option named
Circulation param.
, select the parameter to be changed with
or
, edit the parameter
, change its value
with
or
, accept (a continuous sound)
, return to the main screen with
.
ATTENTION! For description of all available parameters for the circulation pump, see Table 3 – pages 16-17
5.4 Time program K
This option allows for setting a time program in which a device denoted by K (boiler, electrical heat, heat pump) in a given diagram will be working. In order to set or change the K time
program of devices:
Press the following key combination: starting point - MAIN SCREEN: enter the
MENU
with
(enter password), get to the option named
Parameters setting
with
, enter the
Parameter settings
menu with
, get to the option named
Time program K
with
, enter the option named
Time program K
with
, select time with
or
,
accept operation time (white square) or cancel operation time with
, accept and return (a continuous sound) with
, return to the main screen with
.
ATTENTION! Hourly setting of K are identical to those of the Time program C.
5.5 Heat transfer fluid
A parameter connected with liquid specific heat, it corresponds to a given solidification temperature of a heat carrier. In order to define this parameter read liquid solidification
temperature from the package or contact the seller. In order to set or change the solidification temperature of the liquid used:
Press the following key combination: starting point - MAIN SCREEN: entry into the
MENU
with
(enter password), get to the option named
Parameters setting
with
, enter the
Parameter settings
menu with
, get to the option named
Heat carrier
with
, enter the option named
Heat carrier
with
, change values with
or
,
accept and return (a continuous sound) with
, return to the main screen with
.
ATTENTION ! This parameter is needed for correct calculation of solar collector instantaneous power and summing thermal energy.
5.6 Flow rate
A parameter connected with heat carrier flow. In order to make correct settings:
Press the following key combination: starting point - MAIN SCREEN: enter the
MENU
with
(enter password), get to the option named
Parameters setting
with
, enter the
Parameter settings
menu with
, get to the option named
Flow rate
with
, enter the option named
Flow rate
with
, select the parameter to be changed
with
or
, edit with
, change values with
or
, accept (a continuous sound) with
, return to the main screen with
.
ATTENTION ! Correct flow rate depends on the sort of collectors, type of collectors and overall dimensions.
Set the recommended minimum flow rate to 0.3 l/min for 1 m
2
of active area of the collector (example: 2 collectors with active area of 2.0 m
2
each – minimum flow rate is: 2
2 = 4
0.3 = 1.2 l/min.
Set the nominal (maximum) flow rate to 1 l/min for 1 m
2
of active area of the collector (example: 2 collectors with active area of 2.0 m
2
each – nominal flow rate is: 2
2 = 4
1.0 =
4.0 l/min.
The controller enables cooperation with a mechanical rotameter or
an
electronic flow meter of the G-916 type or any other electronic flow meter.
Select the main flow meter connected to
FLOW1
terminals.
The second flow meter connected to
FLOW2
terminals is by default set as
Electronic G-916.
Measurement: Electr.G916
– cooperation
with an electronic G-916 flow meter.
The controller reads the number of impulses and converts it into the real flow (liters per minute).
Nominal
flow rate
– entry to the nominal flow rate option results in switching P collector pumps on with maximum efficiency. Enter the calculated flow rate value that
results from the number of collectors in the system into the edition field. Next, set the required flow in such a way that the “
Current”
value corresponds to the calculated
value entered before. The required flow can be obtained by changing the rotational speed in option
Collector Pump.
