3
CDR-830
IMPORTANT
T H I S H H B A P P A R A T U S C O N T A I N S
LASER OF CLASS
3
b.
SERVICING OPERATION OF THE APPARATUS
S H O U L D B E D O N E B Y A S P E C I A L L Y
INSTRUTED PERSON.
LASER DIODE CHARACTERISTICS
MAXIMUM OUTPUT POWER: 23 mW
WAVELENGTH: 778 – 787 nm
∗
Refer to page 50.
LABEL CHECK
Shield Case
KUXJ/CA type
Printed on Rear Panel
WYXJ type
USYNLIG LASERSTRÅLING VED ÅBNING NÅR SIKKERHED SAF-
BRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSÆTTELSE FOR STRÅLING
UNSICHTBARE LASER-STRAHLUNG TRITT AUS, WENN DECKEL
(ODER KLAPPE) GEÖFFNET IST! NICHT DEM STRAHL AUSSETZEN!
VRW1094
ADVARSEL
VORSICHT!
Printed on Rear Panel
WYXJ type
WYXJ type
1. SAFETY INFORMATION ...................................... 2
2. EXPLODED VIEWS AND PARTS LIST ................ 4
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM ...... 12
4. PCB CONNECTION DIAGRAM .......................... 36
5. PCB PARTS LIST ............................................... 46
6. ADJUSTMENT .................................................... 50
7. GENERAL INFORMATION ................................ 63
7.1 DIAGNOSIS ................................................. 63
7.1.1 ERROR CODE ...................................... 63
CONTENTS
7.1.2 TROUBLE SHOOTING ......................... 65
7.1.3 ERROR MEESAGE"CHECK TEMP" ..... 67
7.1.4 DISASSEMBLY ..................................... 68
7.1.5 DISAGNOSIS OF CD-R CORE ASSY .. 69
7.2 PARTS ........................................................ 70
7.2.1 IC ........................................................... 70
7.2.2 DISPLAY ................................................ 82
8. PANEL FACILITIES AND SPECIFICATIONS .... 84
1. Laser Interlock Mechanism
The position of the switch (S101) on the LOAB Assy for
detecting loading state is detected by the system
microprocessor, and the design prevents laser diode
oscillation when the switch (S101) is not on TRAY terminal
side (TRAY signal is OFF or high level.). Thus, the
interlock will no longer function if the switch (S101) is
deliberately set to TRAY terminal side (low level).
The interlock also does not function in the test mode
∗
.
Laser diode oscillation will continue, if pin 1 of CN101 on
the CD-R CORE ASSY is connected to low level.
2. When the cover is opened with the servo mechanism
block removed and turned over, close viewing of the
objective lens with the naked eye will cause exposure to a
Class 1 laser beam.
Additional Laser Caution
Summary of Contents for BurnIT CDR-830
