background image

Image Kiosk™ TT8870 Programming Guide 

3 - 5

Intercharacter, Interfunction, and Intermessage Delays

Some terminals drop information (characters) if data comes through too quickly.  
Intercharacter, interfunction, and intermessage delays slow the transmission of 
data, increasing data integrity.

Each delay is composed of a 5 millisecond step.  You can program up to 99 steps 
(of 5 ms each) for a range of 0-495 ms.  

Intercharacter Delay

An intercharacter delay of up to 495 milliseconds may be placed between the 
transmission of each character of scanned data.  Scan the 

Intercharacter Delay

 

bar code below, then scan the number of milliseconds and the 

SAVE

 bar code 

using the 

Programming Chart

 inside the back cover of this manual.

To remove this delay, scan the 

Intercharacter Delay

 bar code, then set the 

number of steps to 0.  Scan the 

SAVE

 bar code using the 

Programming Chart

 

inside the back cover of this manual.

User Specified Intercharacter Delay

An intercharacter delay of up to 495 milliseconds may be placed after the 
transmission of a particular character of scanned data.  Scan the 

Delay Length 

bar code below, then scan the number of milliseconds and the 

SAVE

 bar code 

using the 

Programming Chart

 inside the back cover of this manual. 

Next, scan the 

Character to Trigger Delay

 bar code, then the 2-digit hex value 

for the ASCII character that will trigger the delay 

ASCII Conversion Chart (Code 

Page 1252)

on page A-3.

1

2

3

4

5

Intercharacter Delay

Prefix

Scanned Data

Suffix

Intercharacter Delay

Delay Length

Character to Trigger Delay 

Summary of Contents for Adaptus Image Kiosk TT8870






















































































































































Reviews: